Page 1 of 3 123 LastLast
Results 1 to 10 of 25
Like Tree22Likes

Thread: Non mechanical mods that can sub ohm?

  1. #1
    Full Member*
    Join Date
    Oct 2013
    Location
    USA AZ
    Posts
    81

    Default Non mechanical mods that can sub ohm?

    I am already on order for a dna 20 box mod but is there any other mods or e cigs that can sub ohm or atleast fire a 1 ohm coil? Im having trouble looking for a back up
    Leave suggestions please and thank you

  2. #2
    Full Member*
    Join Date
    Oct 2013
    Location
    USA AZ
    Posts
    81

    Default

    VV 18650 w/ Volt Meter always out of stock

  3. #3
    Full Member
    Join Date
    Sep 2013
    Location
    Peck michigan
    Posts
    39

    Default

    A MVP version 2 will fire a 1 ohm

  4. #4
    Surviving Researchista Team ECF (folding@home)
    Verified Member
    State O' Flux's Avatar
    Join Date
    Jul 2013
    Location
    Under the Space Needle
    Posts
    3,411
    Blog Entries
    10

    Default

    Quote Originally Posted by Alejandro Rayas View Post
    VV 18650 w/ Volt Meter always out of stock
    You own/use this... and it will go sub-ohm? I'm asking because of this:

    "All units are tested prior to shipping with various ranges of Atomizers, Cartomizer, and Tank systems from 1.5 ohm to 4 ohm, including Dual Coils."

    Leads one to believe it may have a lower limit... ya' know. :-)

    Quote Originally Posted by Flames11112
    A MVP version 2 will fire a 1 ohm
    All the Innokin APVs will fire at or near 1.0Ω (even the 3.0 )... but they get a "little warm", so I tend to stay above 1.3Ω.

  5. #5
    The Shortest Straw Team ECF (folding@home)
    Verified Member
    ECF Veteran
    Supporting Member
    Thrasher's Avatar
    Join Date
    Oct 2012
    Location
    Madeira beach, Fla
    Posts
    7,752

    Default

    any dna20 mod will do
    the semovar handles 1 ohm
    mechanical with a kick chip

    there not many as sub ohm and regulation dont really go together. sub ohm is basically to counter the non regulation of a mechanical, and when using a regulated output there isnt really a need for high wattage so the choices will be slim.
    gotch23, Baditude, Vash and 1 others like this.

    Semovar - Provari - Roller - Poldiac - Megatron - Nemesis


  6. #6
    Senior Member zhentipede's Avatar
    Join Date
    Apr 2013
    Location
    California, USA
    Posts
    260

    Default

    provari fires 1 ohm but low voltage.... more like 1.2 to 1.5 ohm vapes really well

  7. #7
    PV Master ECF Veteran AttyPops's Avatar
    Join Date
    Jul 2010
    Location
    Hc Svnt Dracones - USA EST
    Posts
    6,863

    Default

    Look at all the above posts. See how they sneak the ohms up and then discuss the real issue: watts.

    If you have a regulated VV device, you can always up the voltage to compensate for the increased ohms. That's not to say that all combinations work, nor that it's 100% identical. But rather, that you can "get a regulated device to work".

    The real question is...do you know the difference between using a sub-ohm coil on a mech, a micro-coil on a mech, a micro-coil on a regulated device, and a standard coil? Turns out you can get a real decent vape a lot of ways.

    So if you don't mind "fudging" stuff a bit to make the electronics work, many of the higher-wattage PVs will work for you. If you insist on 26 ga wire and .5 ohms (or whatever)....well, get a mech and good batteries and a multi-meter and understand it all.
    gotch23, MikeJA, Vash and 5 others like this.
    Tobacco free since 6/30/10 4:30 pm! VV box mod user and amateur multimeter reader.
    ♪♫♪♫♩ They call me AttyPops, AttyPops, Oh Atty Atty Atty... AttyPops! <Ba, Da, Bum, Bum> ♪♫♪♫♩

  8. #8
    Full Member*
    Join Date
    Oct 2013
    Location
    USA AZ
    Posts
    81

    Default

    I dont own just an idea for a possible device

  9. #9
    Full Member*
    Join Date
    Oct 2013
    Location
    USA AZ
    Posts
    81

    Default

    I mostly want a mod for back up that can atleast fire 1 ohm due to have ima use 28 kanthal and make micro coils

  10. #10
    Full Member*
    Join Date
    Oct 2013
    Location
    USA AZ
    Posts
    81

    Default

    Or should i use 30 gauge and buy a normal mod? Do lower ohms vs a timy bit higher ohms make a difference?

Page 1 of 3 123 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •