510 atties w/horrible metallic taste

[telsie]

Is this an epidemic or is it just my bad luck? Of my last six atomizers, only two have been usable. The four bad ones had such a horrible metallic taste that I could not use them at all. I did all the usual stuff: blew out all the primer fluid, put a couple drops of e-liquid on the bridge, did some non-inhaling starter puffs to test the taste. And normally, that's all it takes to get an atty going. Maybe the icky taste will rear its head now and then over the first couple hours of use, but a drop or two of juice will solve it.

With these bad ones, however, I just haven't been able to shake the metallic taste no matter what I do. And this metallic taste is so bad that it seems more like toxic fumes than just unpleasantness from an unseasoned atty. I've noticed these atties are super-saturated with primer fluid — way more than past atties I've had. So I'm wondering if that stuff has permeated the atomizer so much that it's got a permanent industrial taste to it.

Has anyone else been running into this problem? If so, have you managed to solve it? Here's what I've tried:

- Blowing out the primer fluid until no more comes out.
- Flooding it with e-liquid, then blowing it out.
- Dripping a few drops on the bridge.
- Puffing without inhaling then repeating all those steps.
- Dry burning, then adding some drops to the bridge.
- Using an over-filled cart to make sure the bridge stayed extra-moist.

After a couple hours of going through all that, the atomizer(s) still defaulted to horrible metallic taste.

Please help!

[Col. Gaunt]

Is this an epidemic or is it just my bad luck? Of my last six atomizers, only two have been usable. The four bad ones had such a horrible metallic taste that I could not use them at all. I did all the usual stuff: blew out all the primer fluid, put a couple drops of e-liquid on the bridge, did some non-inhaling starter puffs to test the taste. And normally, that's all it takes to get an atty going. Maybe the icky taste will rear its head now and then over the first couple hours of use, but a drop or two of juice will solve it.

With these bad ones, however, I just haven't been able to shake the metallic taste no matter what I do. And this metallic taste is so bad that it seems more like toxic fumes than just unpleasantness from an unseasoned atty. I've noticed these atties are super-saturated with primer fluid — way more than past atties I've had. So I'm wondering if that stuff has permeated the atomizer so much that it's got a permanent industrial taste to it.

Has anyone else been running into this problem? If so, have you managed to solve it? Here's what I've tried:

- Blowing out the primer fluid until no more comes out.
- Flooding it with e-liquid, then blowing it out.
- Dripping a few drops on the bridge.
- Puffing without inhaling then repeating all those steps.
- Dry burning, then adding some drops to the bridge.
- Using an over-filled cart to make sure the bridge stayed extra-moist.

After a couple hours of going through all that, the atomizer(s) still defaulted to horrible metallic taste.

Please help!

I have never had this problem but I have heard that some people use vodka to clean their attys or they boil them. I am not sure for how long though.

[Col. Gaunt]

Just found this, it might help

1 - flush your atty under tap hot water for about 30 seconds or so (you don't need to boil it or make baths with weird stuff for ages, just flush it with hot water for 30 seconds)

2 - blow with your mouth through boths ends (big hole/little hole) of the atty for few seconds to just let it dry a little.

3 - connect your atty to your PV (a regular 3.7v device or ecig) without the cart or cart filler (!!) and perform a 12 seconds (cut-off) dry burn (press the button till cut-off while gently blowing through the mouthpiece -801- or empty cart -510/901- be sure you're blowing -not draggin inside-
you will see a little vapor coming out (it's vaporized water).
If you do not blow while dry burning the coil may get TOO HOT and you may damage it.

4 - do this dry burn 4 times in a row. After that your atty will be perfectly dry and ready to get new juice again.

5 - drip between 5 to 8 drops of liquid into the atty (801), or 2 to 5 (510).
wait a least 2 seconds between any drop, the mesh needs to absorb each drop before adding another one.
Now start vaping, if it doesn't produce much vapor add other drops till it start producing good vapor.
Now the bad taste will be gone.

[Plantgirl]

Colonel Guant, you are my hero!!!I tried everything to get this 510 atty going and your trick did it!!!!!!!

[Col. Gaunt]

I am glad that I could come to the aid of a lady in distress.

Happy vaping!

[telsie]

Thank you very much for the step-by-step instructions, Col.Gaunt. I'm going to give that a try tonight and see if it does the trick. I'll report back later.

[LinkReincarnate]

using unflavored PV can help to get out that metallic taste too. Just blow a bit of unflavored raw PV through it a few times then soak for an hour. Does a pretty good job of getting the gunk out.

[garyd]

If I tried blowing my unflavored PV thru my other PV I think my head would explode, I'm having a hard time just blowing the old juice thru! Haha, lol, just kidding, you meant PG or VG and yes this will work sometimes, sorry just couldn't resist.

[UberDuper]

There's nothing you can do for those atomizers. They're DOA. See if your vendor will replace them. It's a well known defect.

UD.

[Col. Gaunt]

Thank you very much for the step-by-step instructions, Col.Gaunt. I'm going to give that a try tonight and see if it does the trick. I'll report back later.

Your very welcome. I will keep my fingers crossed!