View RSS Feed

Uncategorized

Entries with no category

  1. Innokin Itaste VTR Compatibility - Big List of atomizer's that fit without adapter

    by , 03-11-2014 at 08:45 PM
    Quote Originally Posted by WidowsSon View Post
    Hello,

    I hope this will be useful to any other VTR users out there. Personally I'm not a huge fan of the iClear 30's but still want the protection of the sunken mount... If you've confirmed the fitting of a specific device, post it below and I'll add it to the list.

    So far the Kanger Pro Tank II and the Mega BCC are my favorites in that order.


    NOTE: It's obvious clearmorizers like the iClear16 are going to fit no problem, and all other ego sized devices.
    ...
    Categories
    Uncategorized
  2. Must Have Provari Accessories?

    by , 02-25-2014 at 05:05 PM
    Quote Originally Posted by darkgear View Post
    Here are the MUST HAVES

    Clearomizers
    Kanger Protank 2, Protank 3, Unitank
    Aspire BDC
    Hypertank
    iClear 30
    Vivi Nova
    Smok Tech Pyrex Bottom Coil Tank(PBC)

    Cartomizers
    Ikenvape
    Boge
    Smok

    Tanks
    IBTanked
    Kir Fanis Prive, Prive Special, Prive Veradero
    GP SnP
    ByLeo DBase, Slim Protank
    Bella
    Phiniac
    Little Mama tank
    Fluid Flask
    Loki Labs SS1
    Vaperfexion
    ...
    Categories
    Uncategorized
  3. Heat Treatment/Torching to Color Stainless Steel and Titanium

    by , 02-02-2014 at 04:57 PM
    Quote Originally Posted by Sero View Post
    Lately, I've been seeing a lot of mods that are colored using the heat treatment/torching method. The results I've seen have varied greatly from spotty and poorly done to uniform, professional grade finishes. Some mods have many colors in the finish (JM 22) and some are finished in one uniform color like blue. (Nemesis)

    I would like to know if anyone has any insight on the processes for how this is done as I would like to do this myself one day. I have read things like a propane torch
    ...
    Categories
    Uncategorized
  4. VAMO OHM Error FIX!

    by , 12-03-2013 at 12:34 PM
    Quote Originally Posted by KerryK View Post
    So my new VAMO started reading OHM's like 9.9ohm and certain 510 devices stopped working. This link on Reddit was posted in a thread here on ECF, it was a huge find for me so I wanted to give it more attention.

    The problem is from over-tightening and pushing the center pin down too far. There is a small white gasket that needs to be under the center connection, this pushes up the center pin to make the connections. If the gasket is missing or the center connection is pushed into
    ...
    Categories
    Uncategorized
  5. V3 Pin Rubber Grommet Replacement Mod

    by , 12-03-2013 at 12:29 PM
    Quote Originally Posted by Trayce View Post
    Sadly, Vamos use the same stinky-a@@ rubber grommet used in heads, as a gasket for the positive pin. So after going to all the trouble to replace the rubber grommet in my heads with silicone tubing, I could still detect a faint taste of rubber. When the pin gets hot, I believe it heats the rubber grommet enough to release fumes that get sucked up the airhole in the head pin.

    Long ago I read the "Vamo OHM Fix" thread about a different problem whose fix calls for replacing the
    ...
    Categories
    Uncategorized
Page 1 of 9 12345 ... LastLast