E-Cigarette Forum - Blog Entries - Blogs
View RSS Feed

All Blog Entries

  1. Protank Cotton Rebuild, the way I do it

    by , 09-20-2013 at 05:25 AM
    Quote Originally Posted by metalhed73 View Post
    Pull Some cotton off of the ball, you really don't need much:
    Attachment 253466

    Roll the cotton into a thin wick with one end tapered to make it easier to thread through the coil:
    Attachment 253467

    Thread through the coil until you encounter resistence enough to move the coil instead of sliding cotton through (this would be the time to make final adjustments to the coil if needed):
    Attachment 253468

    Trim
    ...
    Categories
    Uncategorized
  2. Protank Cotton Rebuild, the way I do it

    by , 09-20-2013 at 03:12 AM
    Quote Originally Posted by metalhed73 View Post
    Seen a lot of questions regarding rebuilding protank/evod/every clone that takes them heads. So i figured I would post up my process and what I have learned so far.

    What you will need:
    Click image for larger version. 

Name:	20130903_111357.jpg 
Views:	176 
Size:	21.5 KB 
ID:	253456

    Disassemble the head:
    Click image for larger version. 

Name:	20130903_111457.jpg 
Views:	151 
Size:	19.9 KB 
ID:	253457

    Wrap the coil on the drill bit:
    Click image for larger version. 

Name:	20130903_111842.jpg 
Views:	210 
Size:	20.7 KB 
ID:	253458

    Put Coil in the head:
    Click image for larger version. 

Name:	20130903_111924.jpg 
Views:	487 
Size:	20.0 KB 
ID:	253459

    Insert rubber insulator and
    ...
    Categories
    Uncategorized
  3. Perfect Micro Coils Made easy

    by , 09-19-2013 at 04:24 AM
    Quote Originally Posted by Vapeaddikt View Post
    I haven't been happy with my coils. They were not bad but there were not as "good" as they could be.

    I started thinking over the past few days and just let me mind digest on the idea.

    If this method has been illustrated (which it most likely has) I apologize in advance but always like to share ideas related to a hobby.

    Before we start this though:

    Disclaimer: if you choose to try this this method of doing coils you do so at your own
    ...
  4. RM2 FULL atomizer itself rebuild

    by , 09-19-2013 at 04:22 AM
    Disclaimer: This is a full dissection and rebuild tutorial for the RM2 (older not newest model that will come later). If you are not mechanically inclined or have any doubts do not attempt this. This being said, if you choose to proceed ECF nor I assume any responsibility for damaging your RM2 or self in the process.



    This being said lets start:
    -What I use
    micro philips head, micro flathead, channel lock pliers and tweezers(tweezers not necessary
    ...
  5. Watts and Volts on a VV/VW Device

    by , 09-19-2013 at 02:39 AM
    Quote Originally Posted by ShariR View Post
    Ok. This is how the volts and watts work on the MVP2 (or any current vv/vw device). If you set the watts to say 7 watts, the device automatically figures out the best volts to run at. You do nothing else but vape. You do NOT do anything to set volts.

    If you set the volts, you need to know what your ohms are on the topper you are using, so you know what volts to set it to, to not get a burnt hit.

    Think of it this way. Watts are red. Volts are blue. Just like two football
    ...
    Categories
    Uncategorized