RN4081 mod (Njoy Pro et al.) - e-cigarette-forum.com • The place for electronic cigarette reviews, news and chat

dibbyb · 05-07-2009, 11:29 AM

I'd take some pics but this is pretty simple.
My problem was refilling these carts with the nozzle-top bottles. The reservoir sits way down in the cart and if you try to drip the juice goes underneath the reservoir and into your mouth when you suck on it. I had to push the white liquid reservoir out of the cart, drip a few drops and drop it back in. Pain in the tush and messy.
So I held a cart up to the light and scratched a mark on the outside where the end of the reservoir sits when it's seated in the cart. Then hacksawed off at that mark. The cart still fits back on the atomizer snugly. Now when the cart is pulled off the reservoir is right there and I can drip into it without removing it from the cart, as easy as a 901.

Jim Davis · 05-08-2009, 03:45 AM

Quote:

Originally Posted by dibbyb

I'd take some pics but this is pretty simple.
My problem was refilling these carts with the nozzle-top bottles. The reservoir sits way down in the cart and if you try to drip the juice goes underneath the reservoir and into your mouth when you suck on it. I had to push the white liquid reservoir out of the cart, drip a few drops and drop it back in. Pain in the tush and messy.
So I held a cart up to the light and scratched a mark on the outside where the end of the reservoir sits when it's seated in the cart. Then hacksawed off at that mark. The cart still fits back on the atomizer snugly. Now when the cart is pulled off the reservoir is right there and I can drip into it without removing it from the cart, as easy as a 901.

Next time, try this. Get a paperclip or wire small enough to fit in the mouthpiece hole. Simply push in insert up, add a few drops and slide it back on the atty. If you spill, push the insert all the way out, clean it with a tissue, and stick it back in.

42109 · 05-13-2009, 07:47 PM

Thanks Dibbyb,
Simple solution to a pita problem. The cutoff sleeve keeps the spacing right, shallower mouthpiece makes it easier to seat the cart when you do have to take it out... I like it!

muldrick · 05-19-2009, 03:20 PM

Like it, like it alot.
I only cut 1 so far, I think I'll cut off the others about 2mm further towards the battery.
If only there was a way to cut all of my carts a quick, clean and easy way.

radiokaos · 05-19-2009, 03:47 PM

I found easy trick for filling the 4081.

Get a syringe, or a blunt needle and then you don't need to do anything.

It will save you time from cutting up your carts, and you can measure the amount of juice you use on a daily basis.

muldrick · 05-21-2009, 09:29 PM

Yes, that's what I've been doing (with an 18 gauge syringe). It's just easier to get to the actual cart when it's cut.

42109 · 05-22-2009, 06:18 AM

I picked up a box at Pilot the other day and was pleasantly suprised to find they don't have the endcap and that second enclosure to gather juice. There are 4 spacers in the bottom of the mouthpiece instead of 2, so you can just slide the cart back in. Matt finish isn't as slippery.

emus · 06-19-2009, 05:35 AM

rn4081 mods:

1. cut end of cart off with hack saw and sand smooth for instant direct drip cart. One cut cart lasts a long time.
2. make a pass through using an old charger (about 4.5 volts and 500mA to 1500mA), a micro switch (3A works great) and a safety fuse.
3. Enlarge the four air intakes with a rat tail file to minimize drag effort.

Result is a high performance pass through. My RN4081 carts are quite durable as I am careful not to over heat them or run them dry. This RN4081 mod produces endless great vapor with very low drag.

05-07-2009, 11:29 AM	#1
dibbyb Full Member Join Date: Apr 2009 Location: Syracuse, NY Posts: 21	RN4081 mod (Njoy Pro et al.) I'd take some pics but this is pretty simple. My problem was refilling these carts with the nozzle-top bottles. The reservoir sits way down in the cart and if you try to drip the juice goes underneath the reservoir and into your mouth when you suck on it. I had to push the white liquid reservoir out of the cart, drip a few drops and drop it back in. Pain in the tush and messy. So I held a cart up to the light and scratched a mark on the outside where the end of the reservoir sits when it's seated in the cart. Then hacksawed off at that mark. The cart still fits back on the atomizer snugly. Now when the cart is pulled off the reservoir is right there and I can drip into it without removing it from the cart, as easy as a 901.

05-19-2009, 03:47 PM	#5
radiokaos USA Supplier Join Date: Mar 2009 Location: Phoenix, AZ Posts: 677 Tweet this post!	I found easy trick for filling the 4081. Get a syringe, or a blunt needle and then you don't need to do anything. It will save you time from cutting up your carts, and you can measure the amount of juice you use on a daily basis. __________________ 10% coupon code for all purchases on www.aromaejuice.com is "ECF".

05-21-2009, 09:29 PM	#6
muldrick Supplying Modder Join Date: Apr 2009 Location: Preston, MD Posts: 191	Yes, that's what I've been doing (with an 18 gauge syringe). It's just easier to get to the actual cart when it's cut. __________________ AtmosUSA, E-Cig mods.

05-22-2009, 06:18 AM	#7
42109 Super Member Join Date: May 2009 Location: S. Indiana Posts: 535	new Npro carts? I picked up a box at Pilot the other day and was pleasantly suprised to find they don't have the endcap and that second enclosure to gather juice. There are 4 spacers in the bottom of the mouthpiece instead of 2, so you can just slide the cart back in. Matt finish isn't as slippery. __________________ LabRat... No Lab. Not in the economic interest of the U.S.A.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-13-2009, 07:47 PM	#3
42109 Super Member Join Date: May 2009 Location: S. Indiana Posts: 535	Thanks Dibbyb, Simple solution to a pita problem. The cutoff sleeve keeps the spacing right, shallower mouthpiece makes it easier to seat the cart when you do have to take it out... I like it!

05-19-2009, 03:20 PM	#4
muldrick Supplying Modder Join Date: Apr 2009 Location: Preston, MD Posts: 191	Like it, like it alot. I only cut 1 so far, I think I'll cut off the others about 2mm further towards the battery. If only there was a way to cut all of my carts a quick, clean and easy way.

06-19-2009, 05:35 AM	#8
emus Super Member Join Date: Jun 2009 Posts: 492	rn4081 mods: 1. cut end of cart off with hack saw and sand smooth for instant direct drip cart. One cut cart lasts a long time. 2. make a pass through using an old charger (about 4.5 volts and 500mA to 1500mA), a micro switch (3A works great) and a safety fuse. 3. Enlarge the four air intakes with a rat tail file to minimize drag effort. Result is a high performance pass through. My RN4081 carts are quite durable as I am careful not to over heat them or run them dry. This RN4081 mod produces endless great vapor with very low drag.