Must Try! ADM auto drip mod

[Metstoo]

Oh boy! I am trying this mod and so far so good. I think I may just have found the answer to my flow problems!

I'm going to try it out for a while and let you know. Thanks Scott!

[Graves935]

I just gave this mod a go and I must say this and the straw are my favorites!

[pvherman]

Working great! Janty eGo with standard poly fill but had to use entire poly fill and roll tight or had leakage ( maybe diff poly from Janty ?) ...gonna try some blue foam on the spring. Thanks much

[JollyRogers]

Trying this now with blue foam. I am at work and didn't have any poly.So far it is good. I cant seem to get my spring down far enough though, so my plug is kind of wrapping around the spring. I was using the brass screen, and refilling is a pain. If the brass screen is left in only 4 drops would "fill" it. So trying this now... using a 901 cart and filling with roughly 10 drops, then tucking the plug in. need just a tad more flow, so may need to trim the plug.

[SCOTTYBALLS]

Trying this now with blue foam. I am at work and didn't have any poly.So far it is good. I cant seem to get my spring down far enough though, so my plug is kind of wrapping around the spring. I was using the brass screen, and refilling is a pain. If the brass screen is left in only 4 drops would "fill" it. So trying this now... using a 901 cart and filling with roughly 10 drops, then tucking the plug in. need just a tad more flow, so may need to trim the plug.

Turn the spring 90 degrees and it will sit lower in the cart..

[Digital Lungs]

I sort of used this idea in my 801 and 901 carts (I'm not fond of round tips). I'm not sure if this idea has been done before, but here goes anyway:

I put the spring in vertically, instead of sideways. I used a small piece of white AquaClear aquarium filter insert foam instead of blue foam or cotton, or whatever else. It seems to work really well, but tastes horrible when run dry. I believe these filter inserts are plastic, so my guess is that they'll last.

The springs help keep the juice in contact with the atty. The filter foam wicks really well.

With this mod variation, especially with the 801 high-bridge atty, the foam can get pushed in, but it'll bounce back when the cart is removed. Prior to using this mod, my 801 high-bridge atties were just not working well with carts, and I was getting very frustrated. Problem solved. This seems to work a lot better than regular carts with my 901 and 510, too.

(Well, I haven't tried it on a 901 atty yet, but I have a 901 cart on my 510.)

[Katattack]

So the real issue is how to explain to friends, co-workers, school mates why after you borrowed their "clicky" pen it doesn't work anymore.

[Trinitrophenol]

Tried this mod using the polly that comes with the 901.. I using it with the chuck's battery mod.. Everything seems alright until the polly dislodged from the cartridge and I sucked up a dollop of ejuice in my mouth while vaping .. Felt a little funny after that.. Gotta try using the blue filter foam instead when I have the chance to go to some aquarium shops..

PS: Is it me or does anyone feels that the filled cartidge runs out faster using this mod? (as compared to the orginal filler)

[Korr]

WOW! This works really good! Thankyou for sharing this mod with us

[dmarnaud2]

Is it me or does anyone feels that the filled cartidge runs out faster using this mod? (as compared to the orginal filler)

No doubt. This mod obviously flows better and thus, since the supply is enhanced, you get "higher" usage rates. I think you'll find that if you are using a high enough nic content for your habit that you usage might taper off a little. However, if you like more vapor more often you may have to lower your nic content a might.