My Evod build
Results 1 to 3 of 3

Thread: My Evod build

  1. #1
    Ultra Member ECF Veteran Visus's Avatar
    Join Date
    Jun 2013
    Location
    United States
    Posts
    1,076

    Default My Evod build

    Picture story:

    Tools:
    Coil Welder
    Tweezers
    Wrapping rod 1/16 or smaller
    Pliers
    Nail clipper or scizzors
    27ga Nichrome
    30ga Nichrome

    Disassemble EVOD use pliers with a cloth towel to protect and pull the pressure fitted small chimney




    Prepare you 27ga Nichrome and your 30 gauge Nichrome I like ohms @ 1.5-8 for an EVOD so I cut to length of 1.6ohms about an inch and a half.




    Weld your NR & R wires The 27ga Nichrome will act just like a NR wire..





    Wrap your coil around a rod 1/16 or less



    Push your coil on the rod thru the coil head holder and replace the rubber grommet keeping the wires opposite of each other and holding onto the rod
    replace the positive pin carefully it will push up your coil use a little vg so it slides in easy. Clip off excess wire



    Reassembly to base, dry burn, and tweeze coil after dry burn while the coil is glowing red so the coil is tight.
    When it glows from the middle its ready for wick




    Prepare and cut the oxidized ss mesh so its loose inside the coil use small strands of silica to pressure fit the ss mesh wick in the coil
    Dry burn the now fitted ss mesh and twist it with tweezers until there are no shorts and it glows from inside out, middle to the ends.



    Reassemble and vape the greatest evod ever, it's an amazing inexpensive powerful vape.. For an added bonus enlarge the 3 base airholes to 1/16


    Last edited by Visus; 03-26-2014 at 01:57 PM.

    Visus Pronounced "Vice'us"

  2. #2
    Super Member Verified Member Dampmaskin's Avatar
    Join Date
    Jan 2014
    Location
    Norway
    Posts
    828
    Blog Entries
    2

    Default

    That's a pretty build, and a nice tutorial. But for those who don't own a wire welder, IME micro coils don't need NR legs, because so little of the total wire length make out the legs.
    Steam Engine - calculators for wrapping coils, checking battery drain, and mixing e-juice.

  3. #3
    Ultra Member ECF Veteran Visus's Avatar
    Join Date
    Jun 2013
    Location
    United States
    Posts
    1,076

    Default

    Quote Originally Posted by Dampmaskin View Post
    That's a pretty build, and a nice tutorial. But for those who don't own a wire welder, IME micro coils don't need NR legs, because so little of the total wire length make out the legs.
    Depends on what wattage your using it with.. If cranking up micro's with no NR wire I can taste the grommet. I have tried it a million times and same outcome without the NR wire.. I can build like picasso coils, but whenever I twist tha knob up I get grommet-- with the NR wires its all vapor and with ss mesh proper pure flavor.

    I use the evod on ego's or dialed at 8 watts previous to NR wire when rebuilt.. Now I can hit 50 watts with it and no grommet flavor; even @ 6-8watts previous to coil welder rebuilt I could slightly taste it. That mod I am holding will hit 70 watts.. I vape @12-17-25watts everyday..

    Wish you could try it the legs stay cool all the way up tha dial to 22 watts and pure flavor.

    I have a build on the iclear 16 that is so badarse its unbelievable.. .5 build and mountains of vapor. I have not seen one of those rebuilt with ss mesh, with a coil welder rebuilds go epic.. Its my haha atomizer when people try it and their eyes tell a story how the heck is this doing this lol..

    Ill do a tutorial when I rebuild it- its not an easy build perhaps one of the most difficult when 1st trying.. But not after you see innokins secret of how its done/made..

    Visus Pronounced "Vice'us"

Tags for this Thread

Bookmarks