New design SLB DSE103 batteries and atomizers (and carts)? - Page 2 - e-cigarette-forum.com • The place for electronic cigarette reviews, news and chat

Ez Duzit · 10-09-2009, 03:34 AM

I've seen a few threads about the auto clean cycle, and they all say the same thing. You should immediately unscrew the battery as soon as you notice the autoclean cycle kick in. Basically, the autoclean cycle is a leftover bit of programming from days gone by. Now it does more harm then good, and isn't necessary anymore. By unscrewing the battery for just a few seconds, you reset the mechanism.

Taelon · 10-09-2009, 05:05 AM

Quote:

Originally Posted by Ez Duzit

You should immediately unscrew the battery as soon as you notice the autoclean cycle kick in.

Sorry, thanks, but you cannot do this fast enough so this will lead to more and baked liquid crust on the heater spiral.

It works with the current atomizer, for now... until it dies, I report then.

Taelon · 10-15-2009, 10:12 AM

Atomizer still stands after many autoclean-cycles.

But the crackling sound at sucking is annoying. Was not with the older model series without middle hole at bottom.

Taelon · 10-25-2009, 11:07 AM

All atomizers dead within a few weeks. Last one seems to be killed by DSE103 usb battery which died too

The old series DSE103 parts stood for months...

Zippy · 10-27-2009, 12:18 AM

Can't start new thread, so I have to ask here.

Earlier today I have bought SLB DSE-084 (aka 8084). Vapor is frustrating. First draw makes fine volume vapor, but all the following look like air.

I've noticed that atomizer resistance to draw in and blow out considerably differs. Despite of what might be expected, normal mean of smoking (draw in) goes harder than blow back into e-cig!
Is it a regular atomizer behavior? Could you check your DSE-084 atomizer, detached from the battery and cap.
I still have 2 weeks warranty to change the device if atomizer proven to be defect.

Ez Duzit · 10-27-2009, 03:13 AM

Quote:

Originally Posted by Zippy

Can't start new thread, so I have to ask here.

Earlier today I have bought SLB DSE-084 (aka 8084). Vapor is frustrating. First draw makes fine volume vapor, but all the following look like air.

I've noticed that atomizer resistance to draw in and blow out considerably differs. Despite of what might be expected, normal mean of smoking (draw in) goes harder than blow back into e-cig!
Is it a regular atomizer behavior? Could you check your DSE-084 atomizer, detached from the battery and cap.
I still have 2 weeks warranty to change the device if atomizer proven to be defect.

Until you have 10 or 15 posts, ( forget which), you can only start a post in the new member section, but you can respond to posts anywhere. Helps cut down on spam.
As far as your e-cig goes, I don't have that model, but the air resistance on all my atty's does feel different when drawing vs blowing. So that is normal.
Make sure your cartridges have juice in them, and the cart filler is not pressed down. It should be almost level with the top of the cart, so when you put the cart on the atty, the filler touches the atomizer, and the juice can wick from filler to atty.
Don't take quick hits like you would a regular cig. First take a quick primer puff just to heat the coil. Then a slow, easy hit for 4-5 seconds.

Here's a few links to help you out.

http://www.e-cigarette-forum.com/for...thank-you.html

FAQs: Frequently Asked Questions About Electronic Cigarettes

Taelon · 10-27-2009, 09:23 AM

Quote:

Originally Posted by Zippy

Can't start new thread, so I have to ask here.

No, You don't. Get out of my DSE103 parts quality thread and respect forum rules you signed at registering

Ez Duzit · 10-27-2009, 12:33 PM

And now we bring you back to our regularly scheduled programming.

Quote:

Originally Posted by Taelon

Atomizer still stands after many autoclean-cycles.

Quote:

Originally Posted by Taelon

All atomizers dead within a few weeks. Last one seems to be killed by DSE103 usb battery which died too

The old series DSE103 parts stood for months...

Well, I warned ya bout those autoclean cycles.

Taelon · 10-27-2009, 01:59 PM

Quote:

Originally Posted by Ez Duzit

Well, I warned ya bout those autoclean cycles.

Well, did not harm the older design attys.

3 new attys from HG just arrived, testing now and avoiding AC with bestecig's DSE103 usb passthru.

3 OHM types, Liquid smells little burned again or HG's new crap liquid, awaiting heater element failure, will report.

Resumed normal operation after 20 puffs, great vapour amount and smell is no more burnt, knock on wood...

Taelon · 11-01-2009, 12:39 PM

Atomizers fine, will keep at HG as favourite seller

10-09-2009, 03:34 AM	#11
Ez Duzit Super Member Join Date: Aug 2009 Location: Southern California Posts: 492 Tweet this post!	I've seen a few threads about the auto clean cycle, and they all say the same thing. You should immediately unscrew the battery as soon as you notice the autoclean cycle kick in. Basically, the autoclean cycle is a leftover bit of programming from days gone by. Now it does more harm then good, and isn't necessary anymore. By unscrewing the battery for just a few seconds, you reset the mechanism. __________________

10-15-2009, 10:12 AM	#13
Taelon ECF Veteran Join Date: Dec 2008 Location: DE Posts: 179	Atomizer still stands after many autoclean-cycles. But the crackling sound at sucking is annoying. Was not with the older model series without middle hole at bottom. __________________ Hardware: 2x M401 2x DSE103, 2x Thin Blue Box 11cm "Health", 3x DealExtreme 84mm Models

10-25-2009, 11:07 AM	#14
Taelon ECF Veteran Join Date: Dec 2008 Location: DE Posts: 179	All atomizers dead within a few weeks. Last one seems to be killed by DSE103 usb battery which died too The old series DSE103 parts stood for months... __________________ Hardware: 2x M401 2x DSE103, 2x Thin Blue Box 11cm "Health", 3x DealExtreme 84mm Models

11-01-2009, 12:39 PM	#20
Taelon ECF Veteran Join Date: Dec 2008 Location: DE Posts: 179	Atomizers fine, will keep at HG as favourite seller __________________ Hardware: 2x M401 2x DSE103, 2x Thin Blue Box 11cm "Health", 3x DealExtreme 84mm Models

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-27-2009, 12:18 AM	#15
Zippy Junior Member Join Date: Oct 2009 Posts: 1	Can't start new thread, so I have to ask here. Earlier today I have bought SLB DSE-084 (aka 8084). Vapor is frustrating. First draw makes fine volume vapor, but all the following look like air. I've noticed that atomizer resistance to draw in and blow out considerably differs. Despite of what might be expected, normal mean of smoking (draw in) goes harder than blow back into e-cig! Is it a regular atomizer behavior? Could you check your DSE-084 atomizer, detached from the battery and cap. I still have 2 weeks warranty to change the device if atomizer proven to be defect.