NEW *AW Battery Importers & Exporters of America* (Shipping Worldwide)
Page 1 of 195 123451151101 ... LastLast
Results 1 to 10 of 1946
Like Tree158Likes

Thread: NEW *AW Battery Importers & Exporters of America* (Shipping Worldwide)

  1. #1
    Accessories Supplier ECF Veteran Wonderlite's Avatar
    Join Date
    Jan 2011
    Location
    Long Island, NYC, Miami USA
    Posts
    705

    Lightbulb NEW *AW Battery Importers & Exporters of America* (Shipping Worldwide)

    Happy New Year! New Lower prices for 2012! Lower prices for shipping, cells, and chargers!

    Greetings ECF members and staff.
    I am a reseller of AW cells in the USA, and worldwide.
    Several of my customers have told me I should be on this site, so here I am.

    I hope to prevent injuries and property loss due to poor quality batteries, and using unapproved chargers. I will only sell safe cells, AW approved chargers, and IMR cells proven to be safe. Please do not use any other chargers that are not listed below. Only charger AW approved but not listed is the PILA IBC charger..its expensive but worth it. Your cells will last longer.
    - It is a good idea to subscribe to this thread. I cannot edit this post after 24 hours.

    Please, Post your general, technical, Vaporizor, ecig, and battery questions in this thread. I will answer them there. Only send me a Private message unless you are sending private information like transaction numbers, shipping info, paypal details, stuff like your home address. I have never owned an Ecig and I would like ECF members to help me answer these questions. If I know the answer to your question I will reply there in case someone else has the same question, I wont have to answer it twice. Besides it will bump the thread! Thanks!

    Quality Batteries By AW with a Proven Safety and Reliability Track Record Since 2005


    AW cells do not Overstate their capacity like other brands. Even though they state a lower MAH capacity, they will last longer.

    If you live in North America, or anywhere, and want the best quality cells, you buy AW. I have already had these shipped here to NYC and Miami from Asia so you can get your AW cells faster and for less money.

    You will get a confirmation from paypal when your order prints and ships.
    thanks


    Shipping
    Expect two to three days (in the CONUS) instead of 7-14 days.
    Why buy off brand unsafe cells from China?

    We sell these for use anywhere in the world, from NYC or Miami.

    These are fresh AW cells that arrive in small shipments, often. They are stored short term at an ideal voltage in a cold environment in airtight waterproof containers.

    you must include your ECF Handle in your paypal notes, and the forum name ECF. I am on more than one. example: "My ECF handle is WonderLite, here is what I am buying." Your address is already provided and we only ship to confirmed addresses unless otherwise arranged.

    Price Drop!
    Shipping on cells only is a mere $4 for up to Eight cells then just add 50 cents a cell thereafter.
    Buy 9 cells add another .50 cents for shipping, buy 10 add $1.00 etc

    - Please use a Multimeter to check the voltages on your cells after use, both before and after charging!



    New Product : Digital Multi-Meter $10.00

    Digital LCD display. 9v Battery included. Probes included.
    refer to picture for proper setup of probes and multimeter (Dial set on 20v DCV) Black wire plugged in lower COM port. Red Wire center port (V Omega Ma)
    Do not forget to turn off the multimeter when not in in use. 9volt battery is replaceable.
    Use caution when using Powered multimeters. These use probes use electricity to test voltages.


    ================================================== ====================



    WARNING: There is no protection circuit on these to control under or over voltage, just an anti explosion vent. Do NOT short Circuit! A Tremendous amount of current will be released.
    These are "safe chemistry" cells that will never "vent with flame" or catch fire on their own as they contain little oxygen unlike LiCo cells.

    AW IMR cells (Red Label) Unprotected only:

    AW IMR 14500 - 600 mah $6.50 each the NEW "AA sized" IMR cell

    AW IMR 16340 - 550 mah $6.00

    AW IMR 18350 - 700 mah $8.00

    AW IMR 18500 - 1100 mah $8.50

    AW IMR 18650 - 1600 mah $9.50

    AW IMR 18650 - 2000 mah 10.50

    AW IMR 26500 "C sized" 2300 mah cells $14.50 (extra shipping charges may apply)

    ===================================



    AW protected cells have an UnderVolt and OverVolt cutoff built in. Will also detect and prevent a short circuit. Place on charger to reset the Protection circuit (PCB) the safest LiCo cells that exist. Also incorporates an anti explosion vent.

    AW Protected LiCo Cells (black label) All LiCo cells have at least 33% more capacity than equivalent IMR cells. Do NOT discharge at more than double the stated Mah capacity. (2C) Do not Charge at more than the stated mah capacity (1C) :



    -AW Protected 18650-31P (3100mah) ---- $19.50 each ***NEW CELL*** In Stock LiNiCoO2 NNP cells. Flat top. Three triangulated raised dots ensure solid cell to cell connection when used in series. IN STOCK
    Max Discharge rate 6.2amps!
    - Featuring a new polyimide insulated ultra thin (0.09mm) pcb connecting flexi strip that is heat resistant to 500F ( instead of a bare metal strip ). This new polyimide insulated flexi strip will protect the battery from a direct short in case the outer plastic wrapper of the battery is torn / damage. The new design also makes these 3100 the slimmest protected 18650-3100 available.



    -AW Protected 18650-29P (2900mah) ---- $17.75 each : LiNiCoO2 NNP cells. Flat top. Three triangulated raised dots ensure solid cell to cell connection when used in series. IN STOCK
    Max. Discharge Rate : 5.8AMPS! Enough for many Ecig mods with more total runtime than IMR.

    Above cells: Flat top, Three triangulated raised dots ensure solid cell to cell connection when used in series. Built with these LiNiCoO2 NNP cells. These cells are the only IMR or LiCo cells that can be discharged down to 3.0 volts safely. A new technology cell just released recently.



    -AW Protected 18650-31P (3100mah) ---- $19.50 each - LiNiCoO2 NNP cells *Flat top. Three triangulated raised dots ensure solid cell to cell connection when used in series.

    -AW Protected 18650-29P (2900mah) ---- $17.75 each - LiNiCoO2 NNP cells *Flat top. Three triangulated raised dots ensure solid cell to cell connection when used in series.

    -AW Protected 18650-26P ( 2600mAH ) ---- $14.75 each *Upgraded *Flat top. Three triangulated raised dots ensure solid cell to cell connection when used in series.

    -AW Protected 18650 ( 2200mAH ) ---- $12.00 each *Upgraded *Button Top Cell

    - AW Protected 18500 ( 1500mAH ) ---- $10.00 each *Upgraded *Button Top Cell

    -AW Protected 17670 ( 1600mAH ) ---- $10.00 each *Upgraded *Button Top Cell

    - AW Protected 17500 ( 1100mAH ) ---- $10.00 each Upgraded button top

    - AW Protected 14500 AA ( 750 mAH ) ----- $ 9.00 each button top

    - AW Protected R123A ( 750 mAH ) ----- $ 6.00 each button top

    The new Protected 17670 (1600mAH), 17500 (1100mAH), 14500 (750mAH) are now available. A few improvements have been incorporated on these new cells :

    - a new protection PCB with a higher current threshold ( up to 5A +/- 0.5A );
    - a removable sticker label to reduce overall diameter;
    - button tops on 17670 and 17500 for better contact without the need for spacers ;
    - steel bottom plate for better wear protection from tailcap springs;

    =======================================
    unprotected LiCo cells: ADVANCED USERS ONLY Do not use these if you don't know what you are doing. If it wont work with a protected cell then you should not try an unprotected cell. There is no protection circuit on these to control under or over voltage, just an anti explosion vent.
    *** All with PTC built-in for thermal protection

    - 18650 ( 2200mah ) ----- 6.50 each
    - 18500 ( 1400mAH ) ---- $5.50 each
    - 17670 ( 1500mAH ) ---- $5.50 each
    - 17500 ( 1100mAH ) ---- $5.50 each
    - 14500 ( 700mAH ) AA---- $4.50 each
    Charger for all cells above this line:
    WF-139 2 cell, 2 channel, Intelligent Lithium-ion Charger for only $15.00 IN STOCK

    (15mm Charing spacers for LiCo RCR123 and IMR 16340 required, see below)

    - 15266 ( RCR2 ) 350mAH ---------- $4.50 each

    - 10440 ( AAA ) 350mAH ----------- $4.00 each

    - 14250 ( 300 mAH ) 1/2AA -------- $4.50 each

    - 10280 ( 180 mAH ) ---------------- $4.50 each

    - 10180 ( 90mAH ) ------------------ $4.50 each

    ==================================================
    Safe Chemistry LiFePO4:

    AW LiFePO4 R123 $6.00 each.***

    Chargers for this cell are in stock. the WF-138 R123 charger for 3.0 volt LiFePO4

    ================================================== ======================

    the WF-138 R123 charger for 3.0 volt LiFePO4 and 3.7V LiCO RCR123 and 3.7V IMR 16340 ( has a selector switch for 3.0 and 3.6 setting ). Price : $12.25 each (No spacers needed!)

    Not much choice for the LiCo 10440. Only the WF 138 10440/14500 charger. $12.00

    Pila charger. $45 plus $8 for shipping. (the fastest and the best) 600mah charge rate - 15mm Spacers for charging LiCo RCR123 and IMR 16340/18350 required.

    European charger plugs available for WF 138, WF 139, and Pila. PM for pricing and availablity

    Single channel universal European plug chargers available $10

    ================================================== ========================
    - Spacers for charging RCR2/14270/10280 are $2.00 each with battery purchase

    - 15mm Spacers for charging LiCo RCR123 and IMR 16340/18350 are $1.75 each with battery or charger purchase (for use with WF 139 and many others.)

    - Insulated Dummy CR123 or AA $5.00 each. Made from high quality aluminum they offer zero resistance. (makes a good charging spacer as well. WF 139, PILA IBC)


    Also offering a new model AW approved WF 139 Charger for 15.50 for LiCo cells with a capacity of 450 mah and up and all IMR cells. Also have a Pila Charger available.
    Disregard Mah Capacity when charging IMR cells. They can be charged at a 5 times greater rate than LiCo cells.
    Only charge LiCo cells at (1C) the listed mah capacity, no more.
    *The LiCo unprotected 10440 needs a low power universal one channel charger or WF 138 AAA model

    Shipping Price Drop!
    Price for cells only is a mere $4 for up to Eight cells then just add 50 cents a cell thereafter.
    Buy 9 cells add another .50 cents for shipping, buy 10 add $1.00 etc

    charger only $3.00
    Spacers only $2.00

    CONUS Add 3$ for insurance please
    Prices are for USA first class with confirmation and tracking.

    some countries Insured shipping suggested.

    Please message Wonderlite for International insured shipping quotes.

    insurance both international and domestic is optional but encouraged highly. I never order personally, without insurance. However few outgoing package from us have been lost.

    USA add only 3$ for insurance.

    Please make your paypal notes as detailed as possible, I wont see them. Dont forget ECF HANDLE. then post here what your ordering.


    Please post Details of your order in this thread. What cells you want and How many of each. IMR or LiCo. Protected or Unprotected. What shipping method you want, and if you want insurance. Then post the same details of what you are buying also in your PayPal notes and include your ECF forum name. Thanks.
    Paypal to WonderLite(AT)aol.com, Include your ECF Forum name, the letters ECF, and Detailed notes of order as well.


    I strongly suggest you purchase a Digital Multi meter to check your cell status.

    ANY other payment method you want is ok. Contact Wonderlite for payment address, Paypal questions, Shipping insurance quotes, and all customer service issues. All other hobby related questions belong here in the thread, I depend on other ECF members to help me answer these questions


    Most questions can be answered in the thread, so others will also get to see the answers. PM only private stuff, that box fills up fast.

    Warranty : All batteries sold are covered by a 90 day warranty from the date of purchase. Please keep the voltage of all LiIon batteries above 3.8V for healthy storage. Recharge as soon as possible when you have run them down. Storing a depleted ( less than 3.6V open voltage ) battery may damage/ shorten life/cycle permanently.


    LiIon Battery Charge Status

    4.2V – 100%
    4.1V – 87%
    4.0V – 75%
    3.9V – 55%
    3.8V – 30%
    3.5V – 0%


    Dispose of these cells after about 24- 32 months by taking them to a recycling center. " LiCo cells degrade as they age, sooner if abused.

    IMR USERS: Attention : These IMR cells have much lower internal resistance than regular LiIon 3.7V cells and they may end up with a higher ending voltage when charged in certain chargers ( especially older version WF-139 charger ). Please check the voltage of them right out of the charger to see if they are above 4.20V when fully charged with your charger. Overcharging above 4.25V may shorten life/cycles. Above 4.50V may even pop them or making them leak. DO NOT use the charger if it seems to overcharge IMR cells.

    LiCo Cells are Laptop PC technology. IMR cells are used in power tools. IMR are inherently safe so no protection circuit is needed. However -> do not short circuit an IMR cell, you will release tremendous amounts of energy! Do not use magnets or spacers inside an E Cig as the risk of short circuit is too high.

    ***DO NOT USE LiIon batteries if you don't know the dangers about them and how to handle them. on handling, charging, storage of LiIon batteries,. Also bookmark Battery University Table of Contents for more info. Use at your own risk***

    Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion rechargeable batteries in charging, discharging and assembly before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. We only recommend using Lithium Ion rechargeable batteries with a control circuit (protection PCB) to assure safe charge, discharge, etc.
    Last edited by Misty; 02-05-2011 at 05:01 AM. Reason: edited as per OP request

  2. #2
    Accessories Supplier ECF Veteran Wonderlite's Avatar
    Join Date
    Jan 2011
    Location
    Long Island, NYC, Miami USA
    Posts
    705

    Exclamation Specs Here

    **** Always exercise caution when using / handling LiIon batteries.

    Charger Reference Guide


    ----------------------------- Charger:
    ----------------------------- Nano-123 --- Nano-AAA --- DSD ---------- UF WF-138 --- UF WF-139
    --- [charging bays] --------> 1 ---------- 1 ---------- 2 ------------ 2 ----------- 2
    --- [charging channels] ----> 1 ---------- 1 ---------- 1 ------------ 2 ----------- 2
    --- [current per channel] --> [~150mA] --- [~150mA] --- [350mA+](6) -- [250mA](7) -- [450mA](8)
    -
    - Battery: ------------------

    - Prot. 14500 ( 750 mAH ) --- yes(2) ----- yes(2) ----- yes(1) ------- yes(2) ------ yes
    - Prot. R123A ( 750 mAH ) --- yes -------- yes(2) ----- yes ---------- yes --------- yes(1)
    -
    - 18650 ( 2200mAH ) --------- yes(2,3) --- yes(2,3) --- yes ---------- yes(2,3) ---- yes
    - 17670 ( 1500mAH ) --------- yes(2,3) --- yes(2,3) --- yes ---------- yes(2,3) ---- yes
    - 18490 ( 1350mAH ) --------- yes(2,3) --- yes(2,3) --- yes(1) ------- yes(2,3) ---- yes
    - 17500 ( 1100mAH ) --------- yes(2,3) --- yes(2,3) --- yes(1) ------- yes(2) ------ yes
    - 14650 ( 1000mAH ) --------- yes(2,3) --- yes(2,3) --- yes ---------- yes(2) ------ yes
    - 14500 ( 700mAH ) ---------- yes(2) ----- yes(2) ----- yes(1) ------- yes(2) ------ yes
    -
    - MP R123 ( 700mAH ) -------- yes -------- yes(2) ----- yes ---------- yes --------- yes(1)
    - 15266 ( 300mAH ) RCR2------ yes(1) ----- yes(2) ----- no(4) -------- yes(1) ------ no(4)
    - 10440 ( 320 mAH ) AAA------ yes(2) ----- yes -------- no(4) -------- yes(2) ------ no(4)
    - 14270 ( 310 mAH ) --------- yes(1) ----- yes(2) ----- no(4) -------- yes(1) ------ no(4)
    - 14250 ( 300 mAH ) 1/2AA---- yes(1) ----- yes(2) ----- no(4) -------- yes(1) ------ no(4)
    - 10280 ( 180 mAH ) --(9)---- yes(1) ----- yes(1) ----- no(4) -------- no(4) ------- no(4)
    -
    - 10220 ( 100 mAH ) 1/2AAA--- included for reference only
    - 10180 ( 90 mAH ) 2/5AAA----
    included for reference only (use 10-20mA coin cell charger)
    -
    Notes:

    (1) yes, with spacer
    (2) yes, with adaptor (such as wires with alligator clips)
    (3) yes, but it will take a long time due to low charging current
    (4) no, charging current is too high
    (5) only in pairs, otherwise charging current may be too high
    (6)
    only one charging channel, so the charging current will be split when it charges two cells at once (see note 5); the DSD charging current depends on the 'wall wart' transformer that is used, the normal stock unit seems to be 350-400mA but some people have used transformers with higher current ratings
    (7)
    dual independent channels, so if two cells are charged they will both see the rated charging current; the UltraFire WF-138 charging current is 250mA per channel; an Additional Feature of the WF-138 is a 4.2V / 3.6V selector for charging 3.7V or 3.0V LiIon cells ( the recessed switch is designed so you won't accidentially move the setting, you'll have to use a paper clip to change the setting manually )
    (8) dual independent channels, so if two cells are charged they will both see the rated charging current; the UltraFire WF-139 charging current is 450mA per channel
    (9) The 10280 cell is a shortened AAA cell that has the diameter of an AAA cell but the length of an N cell


    ***NEW*** AW P18650 -2900

    - Built with LiNiCoO2 NNP cells.

    - Three triangulated raised dots ensure solid cell to cell connection when used in series.

    - PCB protection against overcharge/ over discharge / short circuit.

    - Safety vent with thermal cut off protection.

    - Heat Resistance Layer (HRL) technology that forms an insulating metal oxide layer between the positive and negative electrodes. The layer prevents the battery from overheating even if a short circuit occurs.


    SPECIFICATIONS:

    Nominal Voltage : 3.6V
    Capacity : 2900mAH ( rated at 0.2C discharge 4.2V - 2.5V @ 25℃ )
    Operating Temp. : Charge 0 to 45℃ / Discharge -20 to 60 ℃
    Recommended Charge Rate : 825mA ( ambient temp. 25 ℃ )
    Max. Discharge Rate : 5.8A ( ambient temp. 25 ℃ )
    Dimensions :18.52 X 68.16mm ( +/- 0.3mm )
    =========================
    AW P18650 -26

    Designed for incan lamps and high power LEDs. Good performance even under 3A - 5A draw.

    - Three triangulated raised dots ensure solid cell to cell connection when used in series.

    - PCB protection against overcharge/ over discharge / short circuit.

    - Safety vent with thermal cut off protection.


    SPECIFICATIONS:

    Nominal Voltage : 3.7V
    Capacity : 2600mAH ( rated at 0.2C discharge 4.2V - 2.8V @ 25℃ )
    Operating Temp. : Charge 0 to 45℃ / Discharge -20 to 60 ℃
    Max. Charge Rate : 2.6A ( ambient temp. 25 ℃ )
    Max. Discharge Rate : 5.2A ( ambient temp. 25 ℃ )
    Dimensions :18.52 X 68.16mm ( +/- 0.3mm )





    Size measurements :

    P18650-22 - 18.30 x 67.60mm ( +/-0.05 )
    P18500 ----- 18.45 x 51.33mm ( +/-0.05 )
    P17670 ----- 17.02 x 67.30mm ( +/-0.05 )
    P17500 ----- 17.00 x 51.33mm ( +/-0.05 )
    P14500 ----- 14.33 x 51.33mm ( +/-0.05 )



    ***All the above protected cells have Anti-explosion Vent / PTC ( mechanical thermal protection ) in addition to the electronic PCB protection circuit with parts made in the USA and Japan..



    Size Reference :

    18650 = 168A / 600P
    17670 = 168S / 600S
    18500 = 150A / 300P
    17500 = 150S / 300S
    14500 = AA
    16340 = CR123


    Warranty : All batteries sold are covered by a 90 day warranty from the date of purchase. Please keep the voltage of all LiIon batteries above 3.8V for healthy storage. Recharge as soon as possible when you have run them down. Storing a depleted ( less than 3.6V open voltage ) battery may damage/ shorten life/cycle permanently.


    LiIon Battery Charge Status

    4.2V – 100%
    4.1V – 87%
    4.0V – 75%
    3.9V – 55%
    3.8V – 30%
    3.5V – 0%

    IMR:

    Safe chemistry LiMN 3.7V rechargeable battery is now available in R123 / 18500 /18650 /26500 size. These cells can handle high amperage and is safe to use in series / multi-cell applications. Can be charge with any LiIon battery charger with 4.2V output.


    IMR16340 Specifications :

    Nominal Voltage : 3.7V
    Capacity : 550mAH
    Lowest Discharge Voltage : 2.50V
    Standard Charge : CC/CV ( max. charging rate 1.5A )
    Cycle Life : > 500 cycles
    Max. continuous discharge rate : 4A
    Operating Discharge Temperature : -10 - 60 Degree Celsius


    IMR14500 Specifications :

    Nominal Voltage : 3.7V
    Capacity : 600mAH
    Lowest Discharge Voltage : 2.50V
    Standard Charge : CC/CV ( max. charging rate 1.5A )
    Cycle Life : > 500 cycles
    Max. continuous discharge rate : 4A
    Operating Discharge Temperature : -10 - 60 Degree Celsius
    Size : 14.07mm ( diameter ) x 48.80mm ( height ) +/- .1mm


    IMR18490 Specifications :

    Nominal Voltage : 3.7V
    Capacity : 1100mAH
    Lowest Discharge Voltage : 2.50V
    Standard Charge : CC/CV ( max. charging rate 3A )
    Cycle Life : > 500 cycles
    Max. continuous discharge rate : 8C
    Operating Discharge Temperature : -10 - 60 Degree Celsius


    IMR18650 Specifications :

    Nominal Voltage : 3.7V
    Capacity : 1600mAH
    Lowest Discharge Voltage : 2.50V
    Standard Charge : CC/CV ( max. charging rate 4.5A )
    Cycle Life : > 500 cycles
    Max. continuous discharge rate : 10C
    Operating Discharge Temperature : -10 - 60 Degree Celsius


    IMR26500 Specifications :

    Nominal Voltage : 3.7V
    Capacity : 2300mAH
    Lowest Discharge Voltage : 2.50V
    Standard Charge : CC/CV ( max. charging rate 5A )
    Cycle Life : > 500 cycles
    Max. continuous discharge rate : 20A
    Operating Discharge Temperature : -10 - 60 Degree Celsius
    Size : 26.20mm ( diameter ) x 50.40mm ( height ) +/- .05mm

    Special notes

    - These are flat top cells - cell to cell contract requires some pressure. DO NOT use a magnet in between cells to avoid ' shorts '.


    Caution :

    - Do not over-discharge/overcharge;
    - Recharge empty batteries ( resting voltage below ~3.6V ) as soon as possible. Leaving LiIon batteries in discharged state will incur irreversible damage ( capacity / cycle loss );
    - Do not short circuit ( will release tremendous current );
    - Do not dispose of in fire.
    Last edited by Misty; 02-05-2011 at 04:59 AM. Reason: edited as per OP request 2011-02-04

  3. #3
    Ultra Member ECF Veteran
    Join Date
    Nov 2010
    Location
    Chicago, IL
    Posts
    1,873

    Default

    paypal sent
    Welcome to ECF!

  4. #4
    Triple Guru Verified Member
    ECF Veteran
    Supporting Member
    tybin's Avatar
    Join Date
    Sep 2010
    Location
    WA
    Posts
    31,488
    Blog Entries
    1

    Default

    whoot whoot. Welcome wonderlite !!! Tybin (Tiff)

  5. #5
    My friends call me A.G. Verified Member
    ECF Veteran
    Supporting Member
    AlmightyGod's Avatar
    Join Date
    Nov 2010
    Location
    Vaping Heaven
    Posts
    10,685

    Default

    Welcome aboard!!!

    I'm sure ECF will keep you busy!!!

  6. #6
    Accessories Supplier ECF Veteran Wonderlite's Avatar
    Join Date
    Jan 2011
    Location
    Long Island, NYC, Miami USA
    Posts
    705

    Smile Thanks!

    Quote Originally Posted by tybin View Post
    whoot whoot. Welcome wonderlite !!! Tybin (Tiff)
    A special thank you to you Tybin!

    Quote Originally Posted by AlmightyGod View Post
    Welcome aboard!!!

    I'm sure ECF will keep you busy!!!
    Thanks!

    Quote Originally Posted by benjayman2 View Post
    paypal sent
    Welcome to ECF!
    Benjayman, Please post details of what your are ordering here and in your paypal notes.

    thanks!

  7. #7
    Ultra Member ECF Veteran
    Join Date
    Nov 2010
    Location
    Chicago, IL
    Posts
    1,873

    Default

    Oh I posted them in the notes
    2x14500 aw imr
    2x18650 aw imr

    Thanks again.

  8. #8
    Triple Guru Verified Member
    ECF Veteran
    Supporting Member
    tybin's Avatar
    Join Date
    Sep 2010
    Location
    WA
    Posts
    31,488
    Blog Entries
    1

    Default

    i wonder if they would let you have a section in the modder accessories subsection so your posts would not get lost. It may be worth askin wonderlite.

  9. #9
    PV Master Verified Member
    ECF Veteran
    Supporting Member
    lrd3's Avatar
    Join Date
    Jul 2010
    Location
    n.j
    Posts
    4,574

    Default

    looking good.... welcome to ecf......

  10. #10
    Registered Supplier ECF Veteran B-Rad_The_Mad_Vapr's Avatar
    Join Date
    Oct 2010
    Location
    In a pile of sawdust
    Posts
    3,091

    Default

    I'm looking forward to an AW IMR 18350!!! That will be the batts for my vv mod I'm conceiving

Page 1 of 195 123451151101 ... LastLast

Tags for this Thread

Bookmarks