the Vmod

[Jdsgibson]

I'm not easily offended. Anyways, cocktails...favorite juice to load in the vmod and adult beverage combination?

Sent from my HTC Glacier using Tapatalk

[Scotay87]

I'm not easily offended. Anyways, cocktails...favorite juice to load in the vmod and adult beverage combination?

Sent from my HTC Glacier using Tapatalk

3 Vmods working at once with Bobas, Gorilla Juice, and Liquid Express Honey Flue Cured tobacco (My fav vape over 30mls a month)..... Cocktail was screw drivers with an orange mango juice... Cheers

[Chinner]

Ok guys, I need help loving my vmod please!

I'll start by saying I'm a bottom feeder nutcase. I have a whole bunch of different styles as well as an army of wooden feeders. I love the look and feel of my vmod, generally like how it performs, but for the life of me I can't figure out how to get it to stop making a mess.

I received the new chassis like 2 days ago, and have been using it non stop since, but no matter how careful I am, I always get a pile of juice between the case and the chassis.

I've been reading this thread, have been using all the Squonking techniques provided, and still nothing. I may be an a hole saying this, but IMHO any leaking or seepage or mess when it comes to a feeder mod is simply unacceptable to me.

I'm on the verge of dumping this on the classifieds, please any advice would be appreciated here! Help me love this mod!!

[vikki59]

Chinner, are you using the seals for the atty?? The bottom one (off white), and the one that goes around the outside of the atty.

[Chinner]

Let's see, I have a rubber piece that goes around the atty, a small little washer type thing that sits over the threads, and a little plastic nipple thing over the bottle top. I can't figure out what is going on lol!

[Scotay87]

Try using it without the case to see where your leak or leaks are coming from... If around the the atty/silo make sure you have the newer seal (the one that goes around the atty/carto)and it is clean and dry. When assembling be careful not to over tighten things. The cone just tighten enough to keep the shell from rattling....

[vikki59]

Have you tried vaping with it nekkid?? The vmod NOT you . By doing that you should be able to see where it is leaking from to isolate the issue.

You do need to make sure that when you put the gasket on the outside of the atty that everything is dry. If you are going to be vaping nekkid, what I did was screw the cone on so that it would seat the outer gasket, then take it off, otherwise it will leak.

Edit:
Looks like Scot beat me to it .

[flwrfrog]

Hey, my Vmod showed up in the mail today... but I don't have a charger yet because I was trying to find a place to purchase the AW IMR 14500 batts, the correct 14250 batts, and the charger all at once to avoid a bunch of different shipping fees.

Having med issues and not feeling well for a couple of days has slowed me down from reading all of the earlier posts in this thread...
Can someone point me towards a good site where I can purchase all three items?
Or at least the 14250 3.2v batts and a charger that will do both 3.0-3.7 because I see that the Vapage site not has the 14500's back in stock.

Thanks in advance. =)

***edited: Scratch that... I'm just picking up the extra 14500's and the small charger from Vapage for now since I'm ordering attys anyway. =)
I'll explore the 14250's and a multi batt charger later on. =)

Anyone here use/like any of the vapage juice while I'm ordering?

[proax9]

Chinner-
As stated above- vape without the cover to help spot the leak.
It was stated earlier, and I have run into this as well- sometimes the diameter of the silo / atty is a bit smaller than it should be, making the upper seal that goes around it too loose. I get leaks like crazy but only with certain silos / attys. I place a piece of a label (Brothers or P Touch label) around the silo just above the slots where the juice feeds thru. This makes the seal tight and no leaks, Again, I've found only some of the silos / attys needs this.

[Scotay87]

Hey, my Vmod showed up in the mail today... but I don't have a charger yet because I was trying to find a place to purchase the AW IMR 14500 batts, the correct 14250 batts, and the charger all at once to avoid a bunch of different shipping fees.

Having med issues and not feeling well for a couple of days has slowed me down from reading all of the earlier posts in this thread...
Can someone point me towards a good site where I can purchase all three items?
Or at least the 14250 3.2v batts and a charger that will do both 3.0-3.7 because I see that the Vapage site not has the 14500's back in stock.

Thanks in advance. =)

***edited: Scratch that... I'm just picking up the extra 14500's and the small charger from Vapage for now since I'm ordering attys anyway. =)
I'll explore the 14250's and a multi batt charger later on. =)

Anyone here use/like any of the vapage juice while I'm ordering?

rtdvapor.com is the only place I have found for both batts and the multi vlt charger.... Pretty fast but they will be on vacation thru the 21st...