Need input/USB wall plug - E-Cigarette Forum

Debra · 10-29-2009, 07:38 AM

I ordered a wall plug with a USB plug, thinking I could use it with my passthru, but turns out it was only meant for charging, NOT passthru.

Am I wrong in thinking there is one of these out there SOMEWHERE that will support the use of vaping directly with my passthru?

Debra · 10-29-2009, 08:10 AM

Nevermind.

I found a thread that answers my question.

USB passthrough with wall charger??

kno · 10-29-2009, 09:07 AM

i went to marshalls and got an ipod car/wall charger set for 7.99 it makes my pass work wherever - might wanna check it out

Debra · 10-29-2009, 09:19 AM

Thanks kno... but I already ordered one. LOL
Hope it works. Time will tell.

props76 · 10-29-2009, 01:26 PM

The wall USB I got with my 401 kit is rated at 500mA. Thats a bit on the low side, with only a potential for 2.5 watts. Same as older computers USB port output tho. Your 3.7 batt with an 801 atty is using 4.4 watts. So although the voltage is lower, you are actually using more power and producing more vape.

If I were in a store buying one I would shop around and try and find one that puts out 1000mA/1A so you have the potential for 5 watts (closer to what 5V vatt mods put out)

Debra · 10-29-2009, 03:46 PM

This is the one I bought.
Amazon.com: Coby CA81 Dual USB Power Adapter/Charger (White): Everything Else
It says:
Input; AC 100-240V 50/60Hz Output; DC 5V, 1A
The other one I bought was 4.7V but only .08A. The website I bought it from didn't state this information, but they did state that it was FOR charging. I just asumed it would work. Live and learn. lol

props76 · 10-29-2009, 04:02 PM

Carefull they can be tricking you there... The output is 1 amp BUT there are 2 UBS outlets. So 500ma X 2 outlets = 1 amp total, which unless you are running 2 PT's at the same time, doesn't give you an advantage over a single outlet at 500 ma

props76 · 10-29-2009, 04:26 PM

Here is a 1amp unit

1 Amp High Output USB Travel Charger Adapter with Power Surge Protection

Debra · 10-29-2009, 04:27 PM

props, thanks for that info! I have already ordered, so it's too late. LOL

I have read that some people have them with 500mah, and they are working ok, so hopefully this will work for me. I will post an update when I find out.

props76 · 10-29-2009, 04:30 PM

I have 500 mA, so its not the end of the world. If I had to do it again, I'd be looking for a 1 amp.

I'm sure you will be happy with the one you purchased.

Happy vaping.

10-29-2009, 07:38 AM	#1
Debra Senior Member Join Date: Sep 2009 Posts: 287	Need input/USB wall plug I ordered a wall plug with a USB plug, thinking I could use it with my passthru, but turns out it was only meant for charging, NOT passthru. Am I wrong in thinking there is one of these out there SOMEWHERE that will support the use of vaping directly with my passthru? __________________

10-29-2009, 08:10 AM	#2
Debra Senior Member Join Date: Sep 2009 Posts: 287	silly me Nevermind. I found a thread that answers my question. USB passthrough with wall charger?? __________________

10-29-2009, 09:07 AM	#3
kno Registered Supplier Join Date: Oct 2009 Location: Myrtle Beach, SC Posts: 440	i went to marshalls and got an ipod car/wall charger set for 7.99 it makes my pass work wherever - might wanna check it out __________________ www.iVAPE.net

10-29-2009, 09:19 AM	#4
Debra Senior Member Join Date: Sep 2009 Posts: 287	Thanks kno... but I already ordered one. LOL Hope it works. Time will tell. __________________

10-29-2009, 03:46 PM	#6
Debra Senior Member Join Date: Sep 2009 Posts: 287	This is the one I bought. Amazon.com: Coby CA81 Dual USB Power Adapter/Charger (White): Everything Else It says: Input; AC 100-240V 50/60Hz Output; DC 5V, 1A The other one I bought was 4.7V but only .08A. The website I bought it from didn't state this information, but they did state that it was FOR charging. I just asumed it would work. Live and learn. lol __________________

10-29-2009, 01:26 PM	#5
props76 Moved On Join Date: Sep 2009 Posts: 257	The wall USB I got with my 401 kit is rated at 500mA. Thats a bit on the low side, with only a potential for 2.5 watts. Same as older computers USB port output tho. Your 3.7 batt with an 801 atty is using 4.4 watts. So although the voltage is lower, you are actually using more power and producing more vape. If I were in a store buying one I would shop around and try and find one that puts out 1000mA/1A so you have the potential for 5 watts (closer to what 5V vatt mods put out)

10-29-2009, 04:02 PM	#7
props76 Moved On Join Date: Sep 2009 Posts: 257	Carefull they can be tricking you there... The output is 1 amp BUT there are 2 UBS outlets. So 500ma X 2 outlets = 1 amp total, which unless you are running 2 PT's at the same time, doesn't give you an advantage over a single outlet at 500 ma

10-29-2009, 04:26 PM	#8
props76 Moved On Join Date: Sep 2009 Posts: 257	Here is a 1amp unit 1 Amp High Output USB Travel Charger Adapter with Power Surge Protection

10-29-2009, 04:27 PM	#9
Debra Senior Member Join Date: Sep 2009 Posts: 287	props, thanks for that info! I have already ordered, so it's too late. LOL I have read that some people have them with 500mah, and they are working ok, so hopefully this will work for me. I will post an update when I find out. __________________

10-29-2009, 04:30 PM	#10
props76 Moved On Join Date: Sep 2009 Posts: 257	I have 500 mA, so its not the end of the world. If I had to do it again, I'd be looking for a 1 amp. I'm sure you will be happy with the one you purchased. Happy vaping.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode