The Echo Thread - Part 2

[Cool_Breeze]

Thought it was 9 coils.....that's still a lot of coils to fit in a ce4.........need more info, I'm obviously misunderstanding.

It is 9 coils. Nine coils wrapped around 2 pieces of wick about 2 feet long. If one cuts the wick and wire (not where the coils are wound) half-way between the coils, one gets a single coil with two wicks through it and extending about 1 1/4" either side of the coil. Only one coil is used at a time in the Echo (or other) cartomizer. So, one lenght of wick and wire, properly cut can replace that in a single carto, 9 times, or 3 cartos, 3 times, or, however you prefer your math.

=====////\=====*=====////\=====*=====////\=====, etc.

////\ = Coil
=== = Double Wick
* = Cut Point

[Charlz]

so one of the coils, left as they send it, measures 3.4?.

Sounded like you rewound one of their coils and cut it shorter for the 3.4 ohms.

[CloveHunter]

Thanks for the reply, Don't know if anyone else is affected or not only time wii tell. Keep checking on your CC statements!

Thank you for the warning, lulu - will definitely keep an eye on my CC statements; other than that, I know it's quite a hassle - you have to pay some fee, do every online transaction with a prepaid/charge card and empty it immediately. Should help if this kind of thing happened.

[Cool_Breeze]

...unwound it a turn and a half or so...learning process...when it warms up a little, gets in the range of 4 Ohms. But it doesn't take all that much voltage to vape well. 4.3 Volts or so sets it off nicely. The other 2 I've install are about 4 Ohms cold. They are advertised at 4 to 5 Ohms. Want less..? ...unwrap a turn or two of coil.

Has silica been denounced over in the 'safe wick' thread?

[RugDoctor]

I have a carto question. I have a SC that is about a week old and been vaping 100% vg bobas bounty and now it is giving me a terrible burnt taste, so bad i cant vape it. Is the carto pretty much shot? I ordered a crystal vision clear carto and really love it, but is there a special way to clean them or just keep topping it off?

[Charlz]

Has silica been denounced over in the 'safe wick' thread?

I'm still using it. I've done a couple of experiments with the ce4s but haven't dedicated my life to it yet. Threaded some cotton through a prewound coil on a ce2 as well. That's the real beauty. It's so soft, you can do things you can't with brittle glass wicks. The whole point of the thread is alternatives.

[Charlz]

I have a carto question. I have a SC that is about a week old and been vaping 100% vg bobas bounty and now it is giving me a terrible burnt taste, so bad i cant vape it. Is the carto pretty much shot? I ordered a crystal vision clear carto and really love it, but is there a special way to clean them or just keep topping it off?

It's hard to degunk a vg crusted coil and wick. I'd suggest soaking it for a day or so in PGA then rinsing it. Look through the more involved cleaning methods below. It's a reply to a previous similar question.

It depends on your juice but on average a week or two. After that the coil gets gunked. There are many methods of cleaning them. The bases aren't glued to the shell and can be popped off and completely cleaned for a month or so. Here's the simplified method. Trust me. It's easy. I was not a modder until someone on this forum finally impulsed me to try it and everything I learned, I learned from taking the echos apart. The Echo Thread post #3292 in case your page setup is different.

Another method it to buy a carto flushing kit from Smoktek. It's not a thorough but will get you another week or so. Cartomizer/Atomizer Cleaning Kit - With 10ml Control Syringe, Luer-lock compatible w/cleaning tubes and instructions

Other than that, just avoid the center hole when putting juice in the clearomizer. A syringe is easy and mess free. Wipe of any juice on the rubber piece that tip screws on to. Cleaning them involves pulling out that silicone piece at the top of the post that rests on the wicks; the piece with the metal tube that the tops screws on top and soaking the whole thing in alcohol and dry burning.

[RugDoctor]

Thanks ill try that. Ive just been flushing them with hot water under the tap then baking them in the oven at 250 for drying for the regular SC cartos. Im starting to like these crystal vision clear cartos better.

[whodat2112]

A question on cleaning the clearomizers (vision echo from SmokTek).....Is it necessary to remove the rubber cup before doing a dry burn?
Asking because I am having a hard time finding a pair of tweezers small enough to remove the darn thing.

[Charlz]

don't worry about ruining the coil. It's pretty far down there. Put a thin piece of metal in the metal hole and wiggle it around and up until it's to a place you can tweeze it out. The other thing you can do is remove the o ring that sits at the base of the threads in the top metal ring. Then grip the shell firmly and with a pair of pliers, yank of the metal ring. It will give you more room to work with.

If and when you decide to remove the top metal band, look for the second o ring inside just under the inside lip. Make sure you don't lose them. Some of them, come right off....others are too hard to remove without damaging the threads. A couple of yanks will tell you if you want to remove it or leave it alone.

In other words, yes....you need to remove the rubber piece. You need to let out all the nasty fumes from the dry burn and check the coils. make sure they are evenly spaced and glow red hot. When you have it right, there will be no more smoke off the coil, very little smell and the wick will be nice and white again.