Results 1 to 10 of 10
Like Tree4Likes
  • 1 Post By CHUCKmfnNORRIS
  • 1 Post By CHUCKmfnNORRIS
  • 1 Post By TTK
  • 1 Post By Maptec

Thread: EGO-T with Leaking CE4

  1. #1
    Full Member Verified Member
    Join Date
    Apr 2010
    Location
    CT
    Posts
    31

    Default EGO-T with Leaking CE4

    I have this kit and the CE4 leaks out the bottom on to the battery connections, i have a second CE4 and it does the same thing. i just got a glass tank from highdesertecig.com that came with 2 Smoktech DCT LR cartomizers and there is no problem with leaking. is this something normal with the CE4's? is there something i can do to stop the leaking onto the battery? am i doing anything wrong?
    yiharry0110 likes this.

  2. Advertisement
  3. #2
    Super Member Verified Member
    ECF Veteran
    Salt&PePPer's Avatar
    Join Date
    Jul 2012
    Location
    Bakersfield
    Posts
    557

    Default

    Something normal, not at all.

    This happened to two of them eh?

    Could be technique in assembling and using the units.

  4. #3
    Full Member Verified Member
    Join Date
    Apr 2010
    Location
    CT
    Posts
    31

    Default

    there is no assembly, the CE4 just screws in, no atomizer and cartridge. they thread in just fine, no cross-threading at all. they are not getting flooded either. i never over fill them, i dont fill over 3/4.

  5. #4
    Full Member Verified Member
    ECF Veteran
    Maptec's Avatar
    Join Date
    Jul 2012
    Location
    Indiana
    Posts
    99

    Default

    Are you screwing them all the way down? I have found that the center post does not always like to pushed in all the way. The other thing is the mouth piece, when you hold it up to the light do you see a small gap?

  6. #5
    Full Member Verified Member
    Join Date
    Jul 2012
    Location
    Seymour, CT USA
    Posts
    46

    Default

    Chuck, I'm using ce4's on eGo Twists for about 2 weeks now and have no issues at all. Just screw'm on and vape. I'm using 3 different ones for 3 different juices, 1 for Bobas, 1 for Mad4, and another for snickerdoodle. The bobas is 100% VG and very thick, and the other 2 juices are 70/30 PG/VG.

  7. #6
    Full Member Verified Member
    Join Date
    Apr 2010
    Location
    CT
    Posts
    31

    Default

    i took a better look at it and liquid is going out the air intake hole, and now my battery was filled, so now its useless. i just ordered a itaste and an ego twist battery and a bunch of other stuff.
    cathycy88 likes this.

  8. #7
    TTK
    TTK is offline
    Super Member ECF Veteran
    Join Date
    Sep 2011
    Location
    Johnson City, TN
    Posts
    485

    Default

    Not all CE4s are the same. I have not had any problems with the Vision CE4s. But, one of my suppliers bought several boxes of long wick CE4s from Microcig and everyone that has been sold or used cracked and leaked through the clear plastic near the base plus leaked internally where the metal tube goes into the base. They would last anywhere from 10 seconds to a couple of days before the cracking and leaking would begin.
    cathycy88 likes this.

  9. #8
    Full Member Verified Member
    Join Date
    Apr 2010
    Location
    CT
    Posts
    31

    Default

    my ce4's are the vision ce4's, i have 3, one came with the kit i got and a bought 2 more to go along with it. part of my issue now is the post on the battery isnt tall enough so its hard to get a good connection, and the battery filled with liquid.

  10. #9
    Full Member Verified Member
    ECF Veteran
    Maptec's Avatar
    Join Date
    Jul 2012
    Location
    Indiana
    Posts
    99

    Default

    I have had these issues alot with the non vision CE4's. A few things you can do with this.

    1. Take a pair of needle nose pliers and pull the post out a bit. make sure you screw it down to the battery BEFORE you fill them.
    2. If you have cleaned them, make sure they are dry before you use them again. For some reason they seem to wick too fast if water is still in the wick.
    3. Make sure the mouthpiece is making good contact so that you do not have a gap at the silicon cap.
    4. Do NOT fill them up to the silicon cap. Only fill to the top of the numbers.

    I do not know if you are a chain vaper but I have noticed with with most CE style carts, they will leak a bit if they get to hot or use too much in a short amount of time.

    A lot of us have been through the same issues. Some have success in correcting the issues others have not. I have switched to the kanger T2's and while I have experienced no issues, that is not to say they do not have any flaws.
    cathycy88 likes this.

  11. #10
    Full Member
    Join Date
    May 2012
    Location
    Tullahoma, Tennessee
    Posts
    55
    Blog Entries
    4

    Default

    Don't fill CE4's past the top of the wicks, if you do they will flood, so make sure you stop well short of the silicone piece that sets on top of the wicks, also tilt them on an angle when filling or use a syringe so you don't get any e-liquid in the center hole, if you do it floods the battery. Used properly and with juices that don't crack tanks, CE4's work very well indeed. I have 5 of them and have been using 1 for 2 months now with no problems. I rotate the others but they get less use than the 1 I use for everyday vaping. I also like the T2's, but they vape a bit warm with some juices

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •