5 easy steps to make a atty good as new.

[Scamz]

hi i have done this 4 or 5 times and everytime it has renewed an old clogged up atty that i thought was dead. there are 5 easy steps.

1. If you have a manual battery then press the button then wait and wait about 20 seconds. If you are on automatic then just keep puffing away for about 30 secs trying to got give it any breaks. (this will taste terrible by the way, but this is normal)

2. Blow through your atty at both ends. Start with a smooth soft blow then make it harder and harder until nothing comes out anymore. (yes i am fully aware of what that sounds like, but its the only way i could describe it LOL)

3. Drop your atty in the kettle with water and boil it. Then repeat step 2.

4. Put the Atty in some normal 100% proof vodka over night.

5. Repeat step 2 and 3.

then your atty should be real nice and clean when you look in it. Just put a few drops of juice in it and give it a try. If you don't get any vapor strait away this is more than normal. Just keep puffing away and adding a drop every 10 or so drags.

your atty should be real nice after this, nice light draw, loads a vapor and flavor.

This will not damage your atty if done correctly. although do this at your own risk. i personally have had 100% success rate with this but i accept NO responsibility on anything going wrong if this is done by you.

Good luck and happy vaping.

[doots]

boiling an 801 will kill it dead. dont do it.

[Nepenthy]

Good info, heres my two cents.

Point #1, You can fry your atty with this method if you have blown the atomizer out first. Have direct experience with this. Make sure the atty is wet before you apply voltage for this long.

Point #3, This can melt the seal between the outer casing and the center post. While Ive only experienced this once out of the 4 times Ive boiled, it can happen. Killed a two day old atty this way.

Ive found agitating in a solvent works best. The agitating effect of boiling is probably more effective than the water temp. So if you have a way of agitating the atomizer, in a jewlery cleaner for example, that works well. Simply adding alchohol while plugging the end of the atomizer then capping the other end and shaking will almost always result in black residue chunks on your fingers (a good thing).

Load your atty with plenty of juice after cleaning, if you drip, drip 3 times as much. If you are a cart user, load up a full cart and wait at least 15 minutes for the bridge and wick to absorb plenty of juice.

Its a fine line between killing your atty and cleaning it, which is why you'll find so many methods on this forum. The methods that dont involve heat or straight h20 seem to have the least failure rate, imo.

[AngusATAT]

I advise against boiling, or even soaking an atty in anything.

I blow out my atomizers avery couple of days when the draw seems to get a little harder. That usually clears them up. When it doesn't work, I squirt a little Vodka or Everclear inside with a syringe, plug it with my finger and thumb, give it a .... shaking, then blow out the alcohol from both sides and let it dry a bit. Then just put a couple of drops of juice on the atty bridge and go back to vaping.

My original 6 attys for my 510 have been working well using this method, and I've used them at 6v as well as 3.7v.

[Scamz]

boiling an 801 will kill it dead. dont do it.

well i don't know about the 801 but on my 510 it works a treat.

[ramblingrose]

I just do step 3, blow it out and repeat a couple of times, blow it out and let it dry. Works perfectly. If you don't want to bother with the stove just bring water to boil in a shot glass in the microwave, take it out and drop the atty in.

[mssenterprise]

if u put the atty in alcholol of any kind it will peel the paint off...ive done it

[Basil]

Nuke some coca cola in the microwave and then drop the atty in it - looks good.
(Acids work better with heating)

[Sad Society]

well i don't know about the 801 but on my 510 it works a treat.

Maybe this thread should be about 510 atty's as the OP claims about later in the thread. Remember that not all atty's are the same.

[Scottes]

So far, almost every single post in this thread recommends something different, or a change to the original post.

??


I conclude that any atomizer cleaning method is an opinion, and everyone has a different way.

I'm adopting the Jim Davis Method of cleaning atomizers.