Page 1 of 276 123451151101 ... LastLast
Results 1 to 10 of 2760
Like Tree682Likes

Thread: Iatty

  1. #1
    Forum Supplier ECF Veteran imeothanasis's Avatar
    Join Date
    Feb 2009
    Location
    Athens, Hellas
    Posts
    39,809

    Default Iatty

    An idea of the iatty



    Wick was bought from here:

    http://www.wickstore.com/Products/Ro..._1376-100.aspx

    no resistance wire was bought from here:

    http://www.wires.co.uk/cgi-bin/sh000...#aNI0236_2d050 50g 0.236mm Nickel Wire

    heating wire was bought from here:

    http://www.wires.co.uk/acatalog/nc_bare.html 50g 0.16mm Nickel Chrome Wire
    or if you want thinner wire you can buy 0,122mm ir 0,132mm

    After too many experiments, the best vaping experience with Iatty is with a 1,5 ohm resistance to my opinion. The wick inside Iatty is fat so it can easily handle the liquid demand. And there is also the liquid control that can allow us to use different liquids (thin or fat) and to feed more or less the Iatty. You can still put a thinner wire (0.13 for example) to have more smoke or to be able to put bigger resistance (e.g. 2ohms)
    For 6 volts I recommend 3ohm resistance

    refillings methods if you have a burn taste:
    open close the cap 4-5 times
    open the liquid control more for a continous better taste or close it according to the needs of the liquid you use
    dripping
    Only on GGTS, close the CR and take 3-4 long inhales without pushing the button


    I desided to send 2 different o-rings for the ceramic of the Iatty. You put the very small one first on ceramic and then the bigger one. I did this to make it easier to fit them inside ceramic.

    If you overflood the Iatty just blow from its bottom and the liquid will come out of the mouthpiece. To avoid the overflooding push very good the wick inside slots of the upper plastic

    put all the resistance inside the ceramic otherwise you may damage the plastic under the ceramic

    Make very tight threads and close each other

    Buy 0,13mm wire for even better results
    Last edited by imeothanasis; 07-24-2011 at 12:43 PM.
    I will satisfy every vaper out there


  2. #2
    Super Member Verified Member
    ECF Veteran
    Rick.45cal's Avatar
    Join Date
    Mar 2011
    Location
    Lakeland Florida
    Posts
    832

    Default

    That's awesome Imeo!!!
    “I am enough of an artist to draw freely upon my imagination. Imagination is more important than knowledge. Knowledge is limited. Imagination encircles the world.” ~ Albert Einstein

  3. #3
    Registered Supplier ECF Veteran stv888's Avatar
    Join Date
    Jul 2010
    Location
    Melbourne Australia
    Posts
    191

    Default

    Looks good!

  4. #4
    Forum Supplier ECF Veteran imeothanasis's Avatar
    Join Date
    Feb 2009
    Location
    Athens, Hellas
    Posts
    39,809

    Default

    Thanks Ric and stv. I have vape many atties and none of them produces so much smoke like this one. After the improvements that I want to make it will vape even better, trust me guys.
    I will satisfy every vaper out there


  5. #5
    Senior Member ECF Veteran AldoApache's Avatar
    Join Date
    Feb 2011
    Location
    Portugal
    Posts
    161

    Default

    gimme gimme !!
    good looking project mate! keep up, good luck!

  6. #6
    Supplier Associate ECF Veteran Zoranth's Avatar
    Join Date
    Jul 2010
    Location
    Baldwin, MI. USA
    Posts
    1,052
    Blog Entries
    1

    Default

    Very Interesting Imeo.... Looking forward to see how you progress with this.

  7. #7
    Ultra Member ECF Veteran
    Join Date
    Sep 2009
    Location
    Redneck Rivera
    Posts
    1,830

    Default

    Amazing! GOT THE AVS AND UFS ! O WELL HERE I GO AGAIN

  8. #8
    Super Member Verified Member
    ECF Veteran

    Join Date
    Jan 2011
    Location
    St. Louis, MO
    Posts
    544

    Default

    Neato! Keep the inventions comin Imeo!

  9. #9
    Supplier's Manufacturer - Offline ECF Veteran RippleInStillWater's Avatar
    Join Date
    Jun 2010
    Location
    Land Of Corruption
    Posts
    15,380

    Default

    Hmmm, I figured at that resistance the 6V would be better and it looked it from the clouds at least! Is this the AVS that you were making for the GGTB or a disposable item -- I, as always, am a little confused , it sure looks like a durable item! Great stuff as always, Imeo, and I never get tired of seeing your 'studio', my friend, it makes you that much more human to me..........
    Lady M likes this.

    Z-atty-GGTS, nothing better.......
    Zenfidel and Mixmaster of Ripple Effects Juices at Cigtechs

  10. #10
    Super Member ECF Veteran
    Supporting Member
    zuTma's Avatar
    Join Date
    Oct 2010
    Location
    Croatia, Zagreb
    Posts
    960

    Default

    will it fit in ufs? just kidding
    are you planing to make reusable atty for avs/ufs?

Page 1 of 276 123451151101 ... LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •