Page 3 of 9 FirstFirst 1234567 ... LastLast
Results 21 to 30 of 81
Like Tree53Likes

Thread: ODY using Nextel XC-116 without Moding Ceramic...

  1. #21
    Super Member Verified Member
    ECF Veteran
    thedudeabides's Avatar
    Join Date
    Sep 2010
    Location
    Boston
    Posts
    444

    Default

    Tried your method out tonight MrKrinkle and so far, so good. No leaks and good feedin!
    SS GGTS #014(kicked!), SS GGTS TMF #1459(kicked!) Solid Brass GGTS #4283(kicked!)
    GG Slim, UFS v1, v2, v3, iatty and Odysseus
    RIP: GGTS #378, Wenge/Ebony VV and, Maple/Ebony 3.7v Ali'i

  2. Advertisement
  3. #22
    Ultra Member Verified Member
    ECF Veteran
    MrKrinkle's Avatar
    Join Date
    Feb 2009
    Location
    San Diego, CA
    Posts
    1,293

    Default

    Quote Originally Posted by thedudeabides View Post
    Tried your method out tonight MrKrinkle and so far, so good. No leaks and good feedin!
    Good I'm glad its working out for you... I think the flavor is even better with less wick as well... but that could just be in my head...

  4. #23
    Ultra Member Verified Member
    ECF Veteran
    Ariel_MX's Avatar
    Join Date
    Feb 2010
    Location
    Guadalajara, México
    Posts
    1,765

    Default

    Since I'm outside USA I bought XS-116 instead XC-116, my first try was using the standard setup (wick inside the ceramic channels to the O-Ring on the base), it didn't work very well, I was having dry hits and rare taste, no matter if the juice control was fully open.

    Then I used MrKrinkle's method but with double wick, no leaks, but too much liquid on the wick (high TH and low vapor production).

    Finally I tryied MrKrinkle's method, just one single piece of XS-116, it is working great now

    ~Vaping, it's a lifestyle!~

  5. #24
    Ultra Member Verified Member
    ECF Veteran
    MrKrinkle's Avatar
    Join Date
    Feb 2009
    Location
    San Diego, CA
    Posts
    1,293

    Default

    Quote Originally Posted by Ariel_MX View Post
    Since I'm outside USA I bought XS-116 instead XC-116, my first try was using the standard setup (wick inside the ceramic channels to the O-Ring on the base), it didn't work very well, I was having dry hits and rare taste, no matter if the juice control was fully open.

    Then I used MrKrinkle's method but with double wick, no leaks, but too much liquid on the wick (high TH and low vapor production).

    Finally I tryied MrKrinkle's method, just one single piece of XS-116, it is working great now
    Now try that same single piece of wick with the 0.9ohm dual coil method @ 3.7v and youll be a very happy camper...
    Ariel_MX likes this.

  6. #25
    Full Member ECF Veteran Ace73's Avatar
    Join Date
    May 2011
    Location
    Kentucky
    Posts
    82

    Default

    Do you get any juice at all in the base reservoir using this method MrK?

  7. #26
    Ultra Member Verified Member
    ECF Veteran
    MrKrinkle's Avatar
    Join Date
    Feb 2009
    Location
    San Diego, CA
    Posts
    1,293

    Default

    Quote Originally Posted by Ace73 View Post
    Do you get any juice at all in the base reservoir using this method MrK?
    Actually using this method I have vaped a tank bone dry... what little juice was left was all in the wick... so there is a lot less juice wasted in long saturated lengths of wick and from normal vaping motion all juice eventually finds itself to the short piece of wick....

  8. #27
    Full Member ECF Veteran Ace73's Avatar
    Join Date
    May 2011
    Location
    Kentucky
    Posts
    82

    Default

    Cool. Thank you MrK. In a few days I am due for wick replacement and I am going to try this method. I had been dismantling my XC-116, but that was a pain so I went back to the Ody wick. I must say it is a great idea.

  9. #28
    Ultra Member Verified Member
    ECF Veteran
    MrKrinkle's Avatar
    Join Date
    Feb 2009
    Location
    San Diego, CA
    Posts
    1,293

    Default

    Quote Originally Posted by Ace73 View Post
    Cool. Thank you MrK. In a few days I am due for wick replacement and I am going to try this method. I had been dismantling my XC-116, but that was a pain so I went back to the Ody wick. I must say it is a great idea.
    Try this coil method with my short wick and I think you will be very happy...

    Last edited by MrKrinkle; 04-02-2012 at 10:04 PM.
    Scottinboca and Mosin_Sergei like this.

  10. #29
    ECF Administrator
    Social Groups Manager
    Reviewer/Blogger Manager
    Verified Member
    ECF Veteran
    Supporting Member
    Valsacar's Avatar
    Join Date
    Aug 2010
    Location
    Seoul
    Posts
    1,760

    Default

    Hmm, I might try this on my next coil...


    Above is probably a lie... mmm, more flavours!

  11. #30
    Ultra Member Verified Member
    ECF Veteran
    Mosin_Sergei's Avatar
    Join Date
    Feb 2012
    Location
    Nizniy Novgorod Russia
    Posts
    1,143
    Blog Entries
    2

    Default

    great video, MrKrinkle
    Quote Originally Posted by MrKrinkle View Post
    Try this coil method with my short wick and I think you will be very happy...
    SSGGTS#260\SSGGTS#1117\GGTS#1308\UFS+Bulli SmokeriATTY/ ProVari/FOG/Indulgence/KILA2+AZOT+NIVEL-Powtr Regulated PV

Page 3 of 9 FirstFirst 1234567 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •