First Screwdriver Mod

[LuckySevens4U]

The GG is 6 v. That is what I was thinking. So really the SD isn't anymore powerful than the JS?

[Cisco]

The GG is 6 v. That is what I was thinking. So really the SD isn't anymore powerful than the JS?

The janty stick runs a 3.7v 10440 and I think its about 360mAh. DE sells 10440 with 500mAh with those you could increase the usage on the JS. The SD runs a 3.7v 16340 that is available up to 1000mAh. So the SD will give you almost 3 times more vaping as the standard Janty Stick.


The SD runs one 3.7v cr123a/16340 the benefit is much longer usage before charges, more consistent vaping. My mod runs the same battery type, any cr123a or 16340 will fit. I would recomend using protected batteries only. I left the original on/off click switch on the back end, so basically you can turn it off and put it in your pocket without the fear of it going off.

Now If its 6volts that you want I am not familiar with the GG but you can take a look at this thread. I will warn you that Mod uses 2xcr2 3v UNPROTECTED batteries. But it vapes like a steam locomotive......


http://www.e-cigarette-forum.com/for...v-adapter.html


Cisco...

[ImYourSalt]

great job. if you decide to sell em, let us know!

[Shoresy]

Am thinking on making one of these myself .. Where is the original screwdriver base from to start the mod . The rest of the mod looks fairly simple .

Any help would be gratefully accepted

S

[Kelemvor]

@Cisco, read the user comments on DX the stated 600mAh for the 10440 is not quite right.
i have one janty batterie from the kissbox passthrough, it lasts as long as my 10440 from DX.

personally i fear more what the 6v atomized steam could do to my lungs than any unprotected battery.

sorry for offtopic.

[ApOsTle51]

Am thinking on making one of these myself .. Where is the original screwdriver base from to start the mod . The rest of the mod looks fairly simple .

Any help would be gratefully accepted

S

http://www.dealextreme.com/details.dx/sku.14330

ApO.

[Cisco]

A little visual


Cisco...

[Screamer]

Hey Cisco,

Did you get the last P.M. I sent you?

Still waiting for your reply.

Thanks!!!!

[Cisco]

Hey Cisco,

Did you get the last P.M. I sent you?

Still waiting for your reply.

Thanks!!!!

Screamer,

Check your PM's


Cisco...

[LuckySevens4U]

The janty stick runs a 3.7v 10440 and I think its about 360mAh. DE sells 10440 with 500mAh with those you could increase the usage on the JS. The SD runs a 3.7v 16340 that is available up to 1000mAh. So the SD will give you almost 3 times more vaping as the standard Janty Stick.


The SD runs one 3.7v cr123a/16340 the benefit is much longer usage before charges, more consistent vaping. My mod runs the same battery type, any cr123a or 16340 will fit. I would recomend using protected batteries only. I left the original on/off click switch on the back end, so basically you can turn it off and put it in your pocket without the fear of it going off.

Now If its 6volts that you want I am not familiar with the GG but you can take a look at this thread. I will warn you that Mod uses 2xcr2 3v UNPROTECTED batteries. But it vapes like a steam locomotive......


http://www.e-cigarette-forum.com/for...v-adapter.html


Cisco...

Cisco, if you use PROTECTED batteries in your JS, then it VOIDS your warranty, go figure........lol