Laser Pointer mod Guide

**Cisco** · 08-23-2009, 09:40 PM

Originally Posted by ApOsTle51

my spoon isn't protected , but I havent yet scooped my eye out with it. funny that..

ApO,
I just received my spoon eye gouging protection circuit, if you want I have a few extras......

Cisco...

**ApOsTle51** · 08-23-2009, 09:44 PM

Originally Posted by Cisco

ApO,
I just received my spoon eye gouging protection circuit, if you want I have a few extras......

Cisco...

really ...damn , I've been hunting for one of those for a while now..you truely are the master ..

**dseanor** · 08-23-2009, 11:01 PM

... Cisco Is The Master ...

I Built (2) SuperCisco's - 4081's - Yesterday ...
My Wife Grabbed Them & I Haven't Been Allowed To Touch Them Since ...
She Love's Them, Say's The Best Look, Feel, Hit & Drag She's Found Yet ...

Next Up, 510 Cisco's, I'm Off To Peel A Couple Of 510 Batt's ...
Working On New Battery Connection ...
Pos Terminal Spring Contact Seem's Kinda Flakey ...

Just A Thought ...
What Do You Guy's Think About The Case Being The Positive Contact ???

**Cisco** · 08-23-2009, 11:32 PM

Originally Posted by dseanor

... Cisco Is The Master ...

I Built (2) SuperCisco's - 4081's - Yesterday ...
My Wife Grabbed Them & I Haven't Been Allowed To Touch Them Since ...
She Love's Them, Say's The Best Look, Feel, Hit & Drag She's Found Yet ...

Next Up, 510 Cisco's, I'm Off To Peel A Couple Of 510 Batt's ...
Working On New Battery Connection ...
Pos Terminal Spring Contact Seem's Kinda Flakey ...

Just A Thought ...
What Do You Guy's Think About The Case Being The Positive Contact ???

dseanor,

You can put the battery in either way you like, doesn't matter, unless you have an LED.

By the way,nice job...

Cisco...

**Cisco** · 08-23-2009, 11:34 PM

Originally Posted by Mak

Well I finally made it.
It was quite easy.
510 mod.
Used a 401 USB charger for the connector - remove tag and remove the screw - split case and the connector is there with two wires attached. Unsoldered the connections and now I have a board to make a USB charger with an led.
Connector was larger than the nose cone but there was a ridge that was around a 1/4" diameter and a little bit more than a 1/8" deep, so I drilled out the nose cone just undersized and used a round file and twisted it clockwise which make groves in the nose cone area. I then pressed it in. Did not need to cut down the area above the threaded part either (the threads that screw into the nose cone). Put in some groves or slots for air for a atomizer (small file) as there are none with the connector.
All in all - came out pretty good for my first mod.
Thanks Cisco!

Nice job Mak

Cisco...

**Mak** · 08-24-2009, 12:59 AM

Thanks Cisco - you inspired it for sure. Have used it most of the day and I tell ya the battery last much longer than the standard 510 batts.
Seems to even hold the higher voltage longer - ya know when you first use a battery right off the charger the hit is very good. But after 10 or so hits you can see (feel) the decrease in vaper production. Just ordered a couple of batteries with a charger. I am a happy camper for sure. Thanks again Cisco.

**smiley7** · 08-25-2009, 06:15 PM

Cisco, can you use this type of battery in your mod or 800mah? Titanium NIMH rechargeable battery AAA 1000 mAh (TPEH-TAAA1000) thx

**ceo51378** · 08-25-2009, 08:12 PM

Originally Posted by smiley7

Cisco, can you use this type of battery in your mod or 800mah? Titanium NIMH rechargeable battery AAA 1000 mAh (TPEH-TAAA1000) thx

No. This is a AAA battery, not a 10440 - meaning you will only get about 1.5v out of it which is less than half the voltage you need to fire up the atomizer.

Cisco, this is an excellent mod!!!