Wick materials. Safe vs dangerous.

[nordoe]

Yeah, I think i am using too much cotton. Gonna give it another try tonight.

[bluegrasslover]

Here's a little tool I made. On one side it has a battery connector for taking apart things like phoenix cartos and on the other is the coil winder. The pin has a handle and a little wooden cover so I won't stick myself digging around in my bag any more.

[Flyer]

Great idea!

[mwa102464]

Buy a roll of this SS 316L wool Mesh = Stainless Steel 316L Wool Roll 1 lb Reel - Medium | eBay

Roll a small ball, real small, and Put it under your wick in the Odysseus

Put A small piece in your bottom cap on your Bulli smoker

Anywhere near your coil in a RBA but so it doesnt short it.

Take apart a 510 Atty carefully by removing the tube without messing it up,,,, remove bridge and strip stock mesh around the cramic cup so its clean,,, put a very small piece under the ceramic cup, and wrap a small piece around the ceramic cup and re-install wrapped ceramic cup into the tube.

Pretty much any way you can obtain utilizing a small piece of this near your coils it will double intensify the flavor of your vape, not cheap but works SUPER, splitting a Roll with a friend will leave you with plenty, hope this helps Similar to the mesh used in another popular Atty but I'm using 316L, fine grade will also work as will medium grade, hope this helps some of you out.

[Flyer]

What are the thoughts here on using "mercerized" cotton thread if it has been boiled well 3 times?




EDIT: Found the answer here on page 28 of this thread

"cotton yarn (regardless, make sure whatever you get is 100% cotton and NOT mercerized)"

[Bozothecat]

i use jute twine works really well,cheap and very safe.
20120723_193137.jpg
20120723_193442.jpg

[BJ43]

Buy a roll of this SS 316L wool Mesh = Stainless Steel 316L Wool Roll 1 lb Reel - Medium | eBay

Roll a small ball, real small, and Put it under your wick in the Odysseus

Put A small piece in your bottom cap on your Bulli smoker

Anywhere near your coil in a RBA but so it doesnt short it.

Take apart a 510 Atty carefully by removing the tube without messing it up,,,, remove bridge and strip stock mesh around the cramic cup so its clean,,, put a very small piece under the ceramic cup, and wrap a small piece around the ceramic cup and re-install wrapped ceramic cup into the tube.

Pretty much any way you can obtain utilizing a small piece of this near your coils it will double intensify the flavor of your vape, not cheap but works SUPER, splitting a Roll with a friend will leave you with plenty, hope this helps Similar to the mesh used in another popular Atty but I'm using 316L, fine grade will also work as will medium grade, hope this helps some of you out.

Been using this for years. Fine, medium, coarse.
Lustersheen Stainless Steel Hand Pads ~ Fine | eBay

[jimbill]

i use jute twine works really well,cheap and very safe.
20120723_193137.jpg
20120723_193442.jpg

Great idea what type do you use the brownish looking stuff or the white jute.

[MickeyRat]

What are the thoughts here on using "mercerized" cotton thread if it has been boiled well 3 times?




EDIT: Found the answer here on page 28 of this thread

"cotton yarn (regardless, make sure whatever you get is 100% cotton and NOT mercerized)"

Actually, I believe if you go a little further. The general consensus is that it's not really that bad. We're off in the weeds here though as with a lot of things, there's no way to really know.

[mwa102464]

Been using this for years. Fine, medium, coarse.
Lustersheen Stainless Steel Hand Pads ~ Fine | eBay

For finishing and polishing though, I used it for years as well for that, but try it in your Atty's BJ it's super and makes them monsters !!!