801 Ats Don't Work With Passthrough?

[Cellmeister]

Hi Cell,

I am just going to send them back because the ats that I get from DY work perfectly with the passthroughs and I really don't want to fuss with these.

I really appreciate the advice, but I really do not like to fuss with things like that. IMO, it either works or it don't with electronics.

Hi Ocean,

Your Most Welcome.

Please Do Whatever Your Comfortable With. I Was Just Offering Some Suggestions To A Subject Thats Almost A Daily Issue Here.

Hopefully Some Others Will Read The Topic As Well and We Can All Use Our Heads To Come Up With A Better Solution.

I Wish You The Best In Whatever You Do.

Keep Vapin!

[Oceaneco]

Hi Ocean,

Your Most Welcome.

Please Do Whatever Your Comfortable With. I Was Just Offering Some Suggestions To A Subject Thats Almost A Daily Issue Here.

Hopefully Some Others Will Read The Topic As Well and We Can All Use Our Heads To Come Up With A Better Solution.

I Wish You The Best In Whatever You Do.

Keep Vapin!

You are awesome, Thanks!!

[Idahojo]

Becareful doing this though, theres a chance you make disconnect the wire behind the nipple.


Sun- the stamp for the 901 and 801 is in the same spot.
I'll post a pic tomorrow.

Well what's really bizarre is I accidentally completely pulled out the nipple on one of my atomizers. I said a few bad words and laid both pieces on my desk. A few days later I thought I'd just try putting it back in. I grabbed the old pliers and pushed it back in. There was no wire attached to the back side of the nipple or any appearance there had ever been a wire attached to it. The only thing on the back side were those little plastic orings. Well I put it all back together and was shocked IT WORKED and still works to this day.

[breakfastchef]

There was no wire attached to the back side of the nipple or any appearance there had ever been a wire attached to it. The only thing on the back side were those little plastic orings. Well I put it all back together and was shocked IT WORKED and still works to this day.

I took an atomizer apart last night. There was a wire soldered to the center post of the atomizer connection. Trust me, we are not yet vaping wirelessl, yet.

Your wire broke off when you pulled the center post out. The wire that was soldered to that piece is very stiff and is making a mechanical connection to the part you re-inserted back into your atomizer.

[gep]

Here's a suggestion:

State in your descriptions what model your components really are.
Don't say "Penstyle", state that they are DSExxx or RNxxx

Very simple: Penstyle (RNxxxx)

I had the same problem with passthroughs working with atomizers and I don't feel that the customer should have to go through all this marking and separating to use their equipment.
(Cell: Nice work around but I really just want my equipment to function the way it's supposed to without having to tweak them. They should work without all that.)

This is a much simpler solution, IMHO.

Thanks.

[Sun Vaporer]

I took an atomizer apart last night. There was a wire soldered to the center post of the atomizer connection. Trust me, we are not yet vaping wirelessl, yet.

Your wire broke off when you pulled the center post out. The wire that was soldered to that piece is very stiff and is making a mechanical connection to the part you re-inserted back into your atomizer.

Breakfeast---you are spot on my friend. I have taken apart over 50 of these good old unreliable atomizers and the center contact has the posititive wire that runs up to one side of the coil and the outer ring of the contact has the negitive with that runs to the other side of the coil. The contact point tha tht usually fails is at coil due to the residual build up--Sun

[aasupplyny]

Hi Sun,

Heres the pic of a SLB Pen atomizer.

Picture came out kinda bad. Its so hard to take close up shots.

[Idahojo]

I took an atomizer apart last night. There was a wire soldered to the center post of the atomizer connection. Trust me, we are not yet vaping wirelessl, yet.

Your wire broke off when you pulled the center post out. The wire that was soldered to that piece is very stiff and is making a mechanical connection to the part you re-inserted back into your atomizer.

This atomizer went to a RN4072. I can't believe it still works. That is so strange. The ecig God must be smiling on me! LOL

[KreeL]

I am expecting my order from MyVaporStore to arrive any moment. I also ordered the 801 passthru along with 3 atms and some cartridges. I will post back my results after I set it up.

[KreeL]

Okay. This afternoon my 801 passthru arrived with atms/carts/mocha and marlboro juice exactly as ordered. I just got it all hooked up....AND IT WORKS GREAT!

My first order with MVS has been a super experience! No doubt it won't be the last.

Vic