SmokTech "Mini" RBA - AKA "Squid" tips/tricks
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
Like Tree5Likes

Thread: SmokTech "Mini" RBA - AKA "Squid" tips/tricks

  1. #1
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default SmokTech "Mini" RBA - AKA "Squid" tips/tricks

    I am loving this new Squid - very warm vape, good throat hit. The vapor production is more than sufficient, but I wonder, has anyone tried drilling out the air hole? What size bit did you use? Results?

    Thanks for the feedback~

    Clark

  2. #2
    Ultra Member Verified Member
    ECF Veteran
    UncleChuck's Avatar
    Join Date
    Apr 2011
    Location
    Portland
    Posts
    1,317

    Default

    I have both the "Squid" and the "Phoenix V4" from hoosier, both in SS, they are basically the same aside from a few differences. Anyway, I drilled out the airhole on both to 3mm. I like an airy draw, so that you can either do a slow controlled draw or a few super quick draws and you get great performance either way. I also position my coils as close to the airhole as possible, so that it acts sort of like a drag and adds a bit of resistance to the draw, since the coil + wick are sort of plugging the air hole a bit due to their close proximity to the air hole.

    This really only works well with sub-ohm coils, at higher resistance the coil takes so long to heat up and the vapor produced is thinner to the point where it's incredibly difficult to get a good vape (IMO of course)

    The opposite also seems to be true that smaller holes don't work well with really low resistance coils. Again, just my opinion, but the smaller (stock) air holes don't give enough airflow to properly take advantage of the coil at those power levels. After drilling mine out vapor production seemed to increase by a noticeable amount and the vape got a bit smoother, still great TH but just a tad cooler, and more of a feeling of billowy clouds going into your lungs instead of hot steam, if that comparison makes any sense.

    From what I can tell most people drill theirs out to around the 2mm mark. I'd start small and work your way up as far as size goes. You can always make it bigger, but making it smaller will usually be a hassle involving stuffing stuff into the hole to restrict the airflow a bit.
    Kent Brooks likes this.

  3. #3
    PV Master ECF Veteran Jerms's Avatar
    Join Date
    Jan 2011
    Location
    Fargo
    Posts
    8,557

    Default

    I'm a fan of these. Sun-Vapers has 2 models on sale for $4.79 each, the Cheapie and the Cutie. The Cheapie includes a stainless steel drip tip that alone is worth the price of admission. The Cheapie has the SS cap and uses hex screws (hex rench included) and the cap fits pretty tight. The Cutie has an aluminum cap and the posts are like the Octopus RDA with the thumb screws, and the cap doesn't fit as tight. They both have a tight draw that I like, but may bore it out just a little with a nail.

    I love these small drippers, first the IGO-S and now these. Awesome for contant flavor changers like me and the flavor beats the bigger dripper.

    Sent from my LGL55C using Tapatalk 2

  4. #4
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default

    Quote Originally Posted by UncleChuck View Post
    I have both the "Squid" and the "Phoenix V4" from hoosier, both in SS, they are basically the same aside from a few differences. Anyway, I drilled out the airhole on both to 3mm. I like an airy draw, so that you can either do a slow controlled draw or a few super quick draws and you get great performance either way. I also position my coils as close to the airhole as possible, so that it acts sort of like a drag and adds a bit of resistance to the draw, since the coil + wick are sort of plugging the air hole a bit due to their close proximity to the air hole.

    This really only works well with sub-ohm coils, at higher resistance the coil takes so long to heat up and the vapor produced is thinner to the point where it's incredibly difficult to get a good vape (IMO of course)

    The opposite also seems to be true that smaller holes don't work well with really low resistance coils. Again, just my opinion, but the smaller (stock) air holes don't give enough airflow to properly take advantage of the coil at those power levels. After drilling mine out vapor production seemed to increase by a noticeable amount and the vape got a bit smoother, still great TH but just a tad cooler, and more of a feeling of billowy clouds going into your lungs instead of hot steam, if that comparison makes any sense.

    From what I can tell most people drill theirs out to around the 2mm mark. I'd start small and work your way up as far as size goes. You can always make it bigger, but making it smaller will usually be a hassle involving stuffing stuff into the hole to restrict the airflow a bit.
    This is really good insight I had not yet taken into consideration. I have built a few coils on the Squid despite only having it for a few days... I build a 3 wrap 32gu Kanthal with cotton that hit like a truck (.9ohm), but the throat hit about made me choke... LOL I've been on clearos up until now so all I have is high nic (24mg) juice). In that situation sounds like I need more air coming through to loosen the draw.

    At present I have a freakish build on this sucker... 12 wraps of 32gu Kanthal @ 4.0ohms, also cotton. I am loving the cotton compared to the silica, it seems to wick better and prevent leaks from the airhole. Cotton seems to suck the juice up like crazy. Ironically enough, the 4.0ohm hits BETTER than the .9 ohm with the stock air intake hole... I have been vaping it @ 6v on the Provari - easily the best plume of vapor I have produced thusfar.

    Thank you so much for the input on this, I like the "start small" suggestion.

    Cheers,

    ~Clark

  5. #5
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default

    Quote Originally Posted by Jerms View Post
    I'm a fan of these. Sun-Vapers has 2 models on sale for $4.79 each, the Cheapie and the Cutie. The Cheapie includes a stainless steel drip tip that alone is worth the price of admission. The Cheapie has the SS cap and uses hex screws (hex rench included) and the cap fits pretty tight. The Cutie has an aluminum cap and the posts are like the Octopus RDA with the thumb screws, and the cap doesn't fit as tight. They both have a tight draw that I like, but may bore it out just a little with a nail.

    I love these small drippers, first the IGO-S and now these. Awesome for contant flavor changers like me and the flavor beats the bigger dripper.

    Sent from my LGL55C using Tapatalk 2
    Ironically enough I initially picked this up because I needed to test my DIY batches without having to dump a clearo every time - great minds think alike. I saw that Sun-Vapers deal, it looked like a good one. I think I have the genuine Smoktech version of the Octopus. The seal is sufficient, but it's by no means "tight." I wouldn't trust it in my pocket for sure. I like the thumbscrews a ton (great for a noob dripper like myself, no tools). I had hoped the cap would be SS, but it it's too light to be stainless... it has to be anodized aluminum. That part was disappointing. I picked both of mine up at MVS since I was ordering a Pink Vision Spinner 1300mah as a gift for the old lady... I figured I would save on the shipping. I think I paid about $8.50 for the Octopus and the Squid with the 10% discount code. I may pick up the Cheapie and the Cutie just for the hell of it, at that price, why not... LOL Is there a free shipping deal @ Sun-Vapers? I've never done business with them...

  6. #6
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default

    32 guage Kanthal, 12 wraps, 4.0ohms, cotton wick - hits like a truck @ 6v (Provari)

    Ladiekali likes this.

  7. #7
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default

    Another thing I notices is that the resistance goes DOWN if you don't wrap the coil around the post screws like they do in the stock build. Not sure why, though... I thought the length of the coil only mattered on one side of the post. Might be an aberration...

  8. #8
    PV Master ECF Veteran Jerms's Avatar
    Join Date
    Jan 2011
    Location
    Fargo
    Posts
    8,557

    Default

    Shipping was $2.99 at Sun-Vapers if I'm remembering right. Your coil looks very similar to mine. It's a 10 wrap of 31ga on German silica. 2.5 ohms.



    Sent from my LGL55C using Tapatalk 2

  9. #9
    PV Master ECF Veteran Jerms's Avatar
    Join Date
    Jan 2011
    Location
    Fargo
    Posts
    8,557

    Default

    SmokTech "Mini" RBA - AKA "Squid" tips/tricks-uploadfromtaptalk1369359010242.jpg

    SmokTech "Mini" RBA - AKA "Squid" tips/tricks-uploadfromtaptalk1369359049909.jpg

    Sent from my LGL55C using Tapatalk 2
    Kent Brooks likes this.

  10. #10
    Forum Supplier Kent Brooks's Avatar
    Join Date
    Apr 2013
    Location
    Omaha, Nebraska, United States
    Posts
    12,495

    Default

    Nice mini there brother, very nice... "german" silica? What's difference?

    Sent from my SCH-I535 VZW Samsung Galaxy S3 mod'd with AOKP using Tapatalk 2
    Jerms likes this.

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks