Simple and effective way to boost cart performace. in E-Cigarette Technical; I believe using a straw is a much better way to achieve better juice flow out of the cart. Better ...
-
PV Master
ECF Veteran
I believe using a straw is a much better way to achieve better juice flow out of the cart. Better because although it uses the same mechanism - allowing air to flow in or out of the cart bottom - does so without the possibility of leakage as with the hole.
LINK: Cart Mod for better refilling and longer=lasting cart with consistent vaping
The post hilights ease of refilling but it is the ability to get more juice from the cart so that it lasts longer and does not need to be refilled/topped up so often is the main advantage.
Last edited by kinabaloo; 05-21-2009 at 08:05 AM.
-
Ultra Member
ECF Veteran
Well, got to get some shopping done and just found this thread. Too long to read right now, but I'll be back. There is absolutely fantastic ideas in this forum, so glad I found it!!
-

Originally Posted by
bri1270
Pipeman - I'm fairly confident that the 510 carts and the new 901 carts which are black, oval in shape with a round hole and squarish end similar to the 510 carts are already doing this. I was drilling a hole in my 510 and a couple of pieces came out. It appears that they are already doing this. If you pop off the end cap on the mouthpiece there's a hole in the second plastic cap.
In case someone with a 510 sees this...if you pop the end cap (mouthpiece end) off a 510 cart (checked several, from diff vendors), it does indeed look like a hole is there on the 'inner cart.' However, shine a light through it - there's a nub over it on the inside, the hole does *not* go all the way through. Actually, the hole you see is actually a duplicate of the endcap 'disk' for the mouthpiece..not sure why, guess it's a final attempt to not get any moisture back into your mouth...so, basically, two round disks with holes can be removed from the mouthpiece end of a 510 cart, but there is no hole piercing the inner cart compartment from factory.
Last edited by wegster; 05-21-2009 at 11:38 PM.
-
Forum Supplier
ECF Veteran
Take out filler and put half back
Im sorry if someone already said this.. Big forum and ty guys.. I took half filler out of 801 and set asde in baggie and ut rest back in and bam vapor and easy draw...
-

Originally Posted by
kinabaloo
I believe using a straw is a much better way to achieve better juice flow out of the cart. Better because although it uses the same mechanism - allowing air to flow in or out of the cart bottom - does so without the possibility of leakage as with the hole.
LINK:
Cart Mod for better refilling and longer=lasting cart with consistent vaping
The post hilights ease of refilling but it is the ability to get more juice from the cart so that it lasts longer and does not need to be refilled/topped up so often is the main advantage.
I have tried the straw method with different straws and it didn't do a thing for me. So for most people try the straw method first and if it works for you then that is great....if it doesn't try the hole method.
-
Well, I drilled a hole (smallest bit that I have with a pin vise - probably thinner than a regular safety pin) on my 2 piece 901 cart, on the bottom of the brown piece. 1st attempt was an utter failure, because I drilled the hole little too big. 2nd one was a little better - but the juice was still leaking out when I was refilling. I also tried to block the leakage by putting small Tbag filler on the bottom of the cup, but didn't do much either. Perhaps, 100% pg based liquid is too thin... maybe VG might be better for these hole mods, as they are thicker and less likely to run down.
Since I carry around the carts in my pocket shirts, I don't really want anything to leak out... so I had to toss them. It did hold more liquid w/o waiting time... but more important issue for me is the bounciness of the filler itself. Tea bags didn't work for me as it just gunked down... so I'm willing to find some pillow fillers for it, or fluval or what not.
It just seems like the cartridge filler life is just very short. If I get a day or two out of it, it seems like the filler loses its potential. Perhaps I'm burning little too much with my SD, but for me that's the definite case.
I don't mind topping off often, but only when I can get out some good hits out of it, maybe 10-20 times, not 4-5 times.
4 drops of juice really should do it, but for some great reason, it doesn't.
-
Hi , can you draw the explanation , there might be many people not picturing the scheme,thanks..............
-
I tried this....it helps, but i seem to keep getting juice in my mouth....
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
Forum Rules
Bookmarks