Latest activity
hittman replied to the thread Random DIY mixing and More.
I have a box of Stixx Mixx nets that I haven’t been using much. I have been keeping a bottle of the cookie and Stokkebye mix that I use...
englishmick replied to the thread Deeming Regulations have been released!!!!.
Just saw a segment on BBC World News about vaping in the UK. A Gov representative said they consider vaping to be an important piece of...
Tor R replied to the thread Shinyitis Support Group.
good afternoon folks,
2 out of 3 done, probably need to polish the last one a bit more, And then I have to dremmel out the part that is...
FranC replied to the thread Random DIY mixing and More.
Goodnight to you random folks. :) Sweet dreams.
hittman replied to the thread Shinyitis Support Group.
The shipping wasn’t bad at all so I got a roll of each to try.
FranC replied to the thread Random DIY mixing and More.
Yesterday I came across the box of tobaccos I put away long ago.. Mostly Hangsen but some of others. I determined the box to be 6-7...
WorksForMe replied to the thread Deeming Regulations have been released!!!!.
Phillip Morris is pushing the formation of a congressional tobacco harm reduction caucus. It would have been nice if they would have...
FranC replied to the thread Random DIY mixing and More.
Two full tanks and two empty bottles. Tomorrow I’ll get out the other two mixes I did with bases.
FranC replied to the thread Shinyitis Support Group.
Well, it kind of has. A lot of work got done on the addition to my room.
Daniel Forsyth replied to the thread Shinyitis Support Group.
You may be better off putting a small order in at Zivipf. The prices are very good both for the products and the shipping...
FranC replied to the thread Snails - Response on Threads Part 8.
Goodnight, dale. :)
Daniel Forsyth replied to the thread Shinyitis Support Group.
Thank you so very much Fran :wub: I hope you're weekend has kicked off to a fantastic start!!
FranC replied to the thread Random DIY mixing and More.
Guess you can’t get out of that.
hittman replied to the thread Random DIY mixing and More.
I use a cup of water to wet my fingers for smoothing the caulk.
hittman replied to the thread Shinyitis Support Group.
Wireoptm only has it .8 x .1 and the resistance is much higher.
FranC replied to the thread Random DIY mixing and More.
I put two old batteries in yesterday and have both gone well over 24 hours so I’ll keep those. Will test the next two I use.
FranC replied to the thread Random DIY mixing and More.
Better not have a cup close next time.
FranC replied to the thread Shinyitis Support Group.
Good morning,Dan. :wub: Have a wonderful day,
hittman replied to the thread Random DIY mixing and More.
Yes I will. It came out ok but I always make a mess. This time I knocked over a cup of water.
GeorgeS replied to the thread Why no Tube 21700 Regulated Mods?.
A mech tube mod?
A co-worker had one - used it every day and likely is still using it to this day.
Recall that in a at least decently...
Daniel Forsyth replied to the thread Shinyitis Support Group.
I used to get my wire from FT but my recent order of ribbon wire came from Zivipf NiChrome Flat Wire 0.8x0.2mm / .031*.008" - AWG 25...
FranC replied to the thread Snails - Response on Threads Part 8.
Goodnight, Atty. :)
FranC replied to the thread Random DIY mixing and More.
Now you’ll remember for a while longer.
hittman replied to the thread Random DIY mixing and More.
I went up and did the caulking in the bathroom. I almost forgot how much I hate caulking.
hittman replied to the thread Shinyitis Support Group.
I’m not sure where to get it but might try the .8 and 1.0