It sounds like the Nuppin would be a hit in this house then. Thank you all for answering!
Picked up a V1 Nuppin in the classies. (hope another comes up for you @spiritv)
Does anybody know the o-ring size for the V1?
Thanks for the Info!The Nuppin V1 and V2 both use the same size o-rings
O-Rings - 2Base=1mm CS X 10mm ID & 2Cap=1mm CS X 11mm ID
1x10mm - 1mm X 10mm Metric Buna-N 70 O-ring [N1.00X010] : The O-Ring Store LLC, We make getting O-Rings easy!
1x11mm - 1mm X 11mm Metric Buna-N 70 O-ring [N1.00X011] : The O-Ring Store LLC, We make getting O-Rings easy!
The 1 x 10mm o-rings seem to be perfect for the atty base. the AFC o-rings are a toss-up (depending on how snug you like it) between 1 x 10 and 1 x 11mm. The 10mm ID leaves a slightly looser fit as it stretches a hair more and gets a weensy bit thinner. Buna N 70 (a little less flexible, but holds up to tank cracking liquids better. This is what I use as default for BF mod parts(ECF/pdib)
Use 'em everyday
Found an old picture of what was one of my fav Nuppin' builds for the Reos... a high center parallel.
View attachment 683723
Finally got to see why this atty is so loved around here. Purchased a nuppin from mackman and threw a dual 26 g ss coil in it. Wonderful vape and a joy to build. I may have to try that single parallel build next as that has been one of my go to builds for years. But for now I'm quite enjoying the dual coil build in it as is. I might just need to find another one of these attys. I wanted to try my new entheon this weekend too but I couldn't put the nuppin down for long enough to give it a shot!
Back in their day when I used my 8 Nup's they were a favored mid sized atty despite the somewhat restricted draw for my DLH's; and as said above the high center parallel builds were among my favorite builds in them. But they fell out of use eventually when I began changing over to using only 22mm/24mm/25mm (and occasionally 30mm) atty's on all my gear around two years ago. They and their dedicated Reos are a small part of my historic gear collection now.
Found another old picture of that build above...
View attachment 698365
Back in their day when I used my 8 Nup's they were a favored mid sized atty despite the somewhat restricted draw for my DLH's; and as said above the high center parallel builds were among my favorite builds in them. But they fell out of use eventually when I began changing over to using only 22mm/24mm/25mm (and occasionally 30mm) atty's on all my gear around two years ago. They and their dedicated Reos are a small part of my historic gear collection now.
Found another old picture of that build above...
View attachment 698365
Seems my vaping preference has been working in reverse to yours lately as I've been acquired more restricted lung hit atties like the nuppin.
I'm discovering a lot of older gear that is making me wish I had jumped on the squonk wagon a little sooner. Unfortunately I may need to acquire another cc or bam in order to accomodate all these wonderful new/old attys. Ouch, my wallet!
My preference shifted from tight draw to open too - I no longer use those first few successes - Cyclone, Chalice... But I just opened the Nuppins wide on both sides, and still regularly use them. That draw is fine for me.
I guess I've got a "range" - I also run an Entheon, and a Haku - wide open.
Back in their day when I used my 8 Nup's they were a favored mid sized atty despite the somewhat restricted draw for my DLH's; and as said above the high center parallel builds were among my favorite builds in them. But they fell out of use eventually when I began changing over to using only 22mm/24mm/25mm (and occasionally 30mm) atty's on all my gear around two years ago. They and their dedicated Reos are a small part of my historic gear collection now.
Found another old picture of that build above...
View attachment 698365