Taifun GT Discusion!

[hobbes4]

My favorite Taifun clone is the GT-S from fasttech. The GT-S has a 2mm airhole on the deck and AFC ring. For me, it is a happy medium between the restricted airflow of the GT V1 and the massive airflow of the GT V2.

 

[chanelvaps]

My favorite Taifun clone is the GT-S from fasttech. The GT-S has a 2mm airhole on the deck and AFC ring. For me, it is a happy medium between the restricted airflow of the GT V1 and the massive airflow of the GT V2.

I like that one too but cannot seem to find it anymore. Have you seen it at FT?

 

[hobbes4]

I like that one too but cannot seem to find it anymore. Have you seen it at FT?

They took it down for a while and then re-listed the no-logo version. Aside from replacing some of the orings i haven't had any problems with it.

 

[billherbst]

I like that one too but cannot seem to find it anymore. Have you seen it at FT?

Taifun GT-S clones currently available from fasttech:

GT-S clone #1
GT-S clone #2
GT-S clone #3

 

[Phone Guy]

I didn't know the gt-s was different from the gt1. I never really looked at them because they look the same.

I really like the gt2 a lot. Using it right now in fact.

 

[chanelvaps]

Taifun GT-S clones currently available from fasttech:

GT-S clone #1
GT-S clone #2
GT-S clone #3

thanks Bill-guess I was not looking in the right place

 

[anavidfan]

Hello, Taifun fans. Looks like my Taifun GT2 and all its accessories might get here tomorrow (later for those in a diff time zone) Im very excited and nervous like I always am when I get a new atomizer.''

Any important tips or great how to vid link? Ive been watching a few but I have to watch again tonight.

 

[dems86]

Hello, Taifun fans. Looks like my Taifun GT2 and all its accessories might get here tomorrow (later for those in a diff time zone) Im very excited and nervous like I always am when I get a new atomizer.''

Any important tips or great how to vid link? Ive been watching a few but I have to watch again tonight.

BAM Vaping has a review on YT.

My best tip is you don't need a ton of cotton, and leave it fluffed, don't pack it down or roll it tight. Also, cut the wicks just about flush.

A 2.5mm coil will fit between the posts with just enough room on either side.

Screw the chamber cap on just until it starts to compress the cotton, although this is something you will get a better feel for when actually building and working with it.

Enjoy

THE WGU CLUB
Card Carrying Member/Co-Founder

 

[Phone Guy]

Hello, Taifun fans. Looks like my Taifun GT2 and all its accessories might get here tomorrow (later for those in a diff time zone) Im very excited and nervous like I always am when I get a new atomizer.''

Any important tips or great how to vid link? Ive been watching a few but I have to watch again tonight.

Congratulations! Don't forget to post pictures. We love pictures.

And I 2nd what dems86 said...
I use either 2.5mm or 3mm Coils without a problem. The great thing about the taifun is the ability to angle the coil as needed to fit between the posts. Since the chamber collar moves to wherever you have the wicks coming out.

Just one of the great things (especially about the gt2) it's hard to not build it right. Even a quick hurried not so perfect build still results in a pretty darn good vape.

 

[si.hatch]

Wanted to share some coil porn with you guys, 26ga 2.4mm stanley screwdriver(best investment yet for building coils) 1.2 ohms. Picture is before dryfire and adjusting

 

[dems86]

Wanted to share some coil porn with you guys, 26ga 2.4mm stanley screwdriver(best investment yet for building coils) 1.2 ohms. Picture is before dryfire and adjusting

That is a very pretty coi...what's her name?

THE WGU CLUB
Card Carrying Member/Co-Founder

 

[si.hatch]

That is a very pretty coi...what's her name?

THE WGU CLUB
Card Carrying Member/Co-Founder

Well thank you, i was proud of this one, probably my cleanest freehand coil ive made. No name, no attachments, that way i dont feel bad when i rip them out haha

 

[dems86]

Steam Tuners arrived today (so did XS Tank, I'll snag a pic of it soon, the XS Tank is gonna be my errand runner on the amazetastic 2380 that you see pictures below...I really an in love with this mod)

You can catch a glimpse of Ethel in the second pic [emoji14]

THE WGU CLUB
Card Carrying Member/Co-Founder

 

[Mtek]

Great looking combo. I hope Taifun cleans up the design of The Eye and updates and/or uses the new Dicodes chip.

That being said, I think I'll get a GT II. You can't beat these style tanks for airflow, taste, and all around ease of building. Plus, they are attainable unlike the UT.

 

[Phone Guy]

The ubertoot as I recall was kind of an erlkonigin styled device right? I just never got the performance from that everyone else did. I think the tgt2 is "uber" better [emoji14]

 

[dems86]

The ubertoot as I recall was kind of an erlkonigin styled device right? I just never got the performance from that everyone else did. I think the tgt2 is "uber" better [emoji14]

Ubertoot isn't anything like an Erlk

It's closer to a GT2, just with massive wick channels

THE WGU CLUB
Card Carrying Member/Co-Founder

 

[dwcraig1]

Have a look,

 

[Phone Guy]

Have a look,

That was NOT the tank I thought it was. I saw something I thought was the ubertoot and it was a more sophisticated erlkonigin tank, no clue what it was now... I have been thinking it was the ubertoot, I was wrong.

I'm not sure if it's better than the gt2? The UT I mean... But it looks "interesting".

 

[dems86]

That was NOT the tank I thought it was. I saw something I thought was the ubertoot and it was a more sophisticated erlkonigin tank, no clue what it was now... I have been thinking it was the ubertoot, I was wrong.

I'm not sure if it's better than the gt2? The UT I mean... But it looks "interesting".

Todd has a review too, and BAM Vaping just put a review up also. Both of those are worth a watch

THE WGU CLUB
Card Carrying Member/Co-Founder

 

[chanelvaps]

Which one is giving you a problem. top or bottom?
Let me start with the top one. If it seems too difficult to get it to stay on the groove of the metal top piece just position it evenly on top of the glass and screw on the top, it should all come together. (the o-ring must fit the ID of the metal tank to get this procedure to work. If smaller it just about has to be placed on it groove of the cap to get it together)
20 x 1 mm works best for top of clones.

Alright got the top one in using your method (it is a 20) now how about the bottom one and is that a 19?