wOW THAT'S ONE HELL OF A HANDFULLIt's not pretty, but here's my project from this weekend. My first step into squonking.
Internals are the guts of a Sigelei 150w, FatDaddy BF 510 and 15ml bottle. Box was built using Lexan Polycarboante. Still working on the lid, but its working great so far. The hobo v3 is an angelcigs clone but it had the BF 510 pin so I threw it on in favor of converting any of my other atties to save time this weekend. It will not last long on there.
Had to move the 510 and fill with ca. I have to buy linseed oil etc next pay
Sent from my GT-I9506 using Tapatalk
Immediately after building this, I realized how bulky it is, but not necessarily too large for me. I made it as small as i could while fitting everything inside of it. In retrospect, I could have used a more square size box (like the Hammer Of God quad parallels), but it was a fun process with what I had laying around and $8 worth of Lexan.wOW THAT'S ONE HELL OF A HANDFULL
good to see you are putting the Sigelei 150w to good use though.
Unless you have yeti sized hands I imagine you will be looking for a smaller more comfortable unit once you fall for the squonk.
I run a heavily wicked tricro 26g nichrome, with 7-8 1.6mm ID wraps through the middle and two lots of two 2mm ID wraps up top, it comes in around 0.65 Ohms heats quick has huge flavour, thick vapor and thumpy throat hit, and runs great on a single cell. Worth a try if you like Claptons but want somthing more snappy and easier on the power.Immediately after building this, I realized how bulky it is, but not necessarily too large for me. I made it as small as i could while fitting everything inside of it. In retrospect, I could have used a more square size box (like the Hammer Of God quad parallels), but it was a fun process with what I had laying around and $8 worth of Lexan.
I will say that my next squonker will likely be a Reo or something similar now that I know that squonking is quite a bit more enjoyable and easier than dripping. That and I really don't want to spend another 7 hours on and off building a box that may work but not be aesthetically pleasing lol.
I think I've just held onto variable voltage vaping as a means to not worry about having a charger at work or 3 extra batteries on hand. I definitely prefer a warm to hot dense vape, and have grown quite accustomed to my claptons and other artistic coils. To the future though!
Trico? Got some pics? I'm intrigued lol.I run a heavily wicked tricro 26g nichrome, with 7-8 1.6mm ID wraps through the middle and two lots of two 2mm ID wraps up top, it comes in around 0.65 Ohms heats quick has huge flavour, thick vapor and thumpy throat hit, and runs great on a single cell. Worth a try if you like Claptons but want somthing more snappy and easier on the power.
...On the subject of the FD V5, and you may be able to help me here Quigs, where is the sealing o ring for the main shaft. I have massive stock of the V4 flat top and the brass bf cores and although they have their limitations I like the dismantle able nature of them and the ability to change and/or upgrade the orings or even the whole core for that matter. I don't have an issue with the brass as I run a drift fitting 2mm OD 1.6mm I'd ss tube through the core, although cutting and installing this is an extra job tha takes some time obviously. How tight and smooth is the clearance of the pin in the ceramic sleeve?
With my current MOSFET box I get around 0.15v drop on a 0.65ohm build with the brass FD and that still impresses me every time I check it on the volt meter. I wonder what the effect of the Ss pin will be on that.
Getting a little low on feed tubing...anyone got a good line on anything?
Trying to decide if I like regulated squonking.
Now I can squonk on this.
Or this
Or even this.
Yes that's pretty much where I got the idea from. Just have to flop things around a little.that is really great!, you could use a ignition for a side by side
Nice Crocks!
For size
I know. Everyone has built a hammond squonker. Exciting for me though
Sent from my GT-I9506 using Tapatalk