The easy route
Can't resist an offer
The easy route
Of course notCan't resist an offer
Do you mean pre mix flavoured or base ?JC is now doing pre-mix and 10ml nic shots, interesting but I thought TS said pre-mix had to be 10ml too as he is doing big bottles of pre-mix?
Good!At the risk of being repetitive, coil still going.
I suppose, as it's nothing that has hit the news networks as a breach of law/regulations, that they'll continue selling online until such time as they are told otherwise (or not) ...fingers crossed!JC is now doing pre-mix and 10ml nic shots, interesting but I thought TS said pre-mix had to be 10ml too as he is doing big bottles of pre-mix?
Nothing stopping you getting a few of those cheap 10ml bottles to hand though!Yes Cabin kits you get a full kit with nic but it only goes up to 12mg strength. Asked him if he could do an 18mg kit but he said not now.
If he say`s another 2% then roughly that would be another 20 drops. So a full bottle plus 20 drops 10 drops equals 1 mlYea but how much to add to get 12mg to 18mg. Have asked on his Facebook page but he said you could only add another 2%.
In all honesty you would be better off just starting from scratch, get some plain pg/vg/concentrate/nic and away you go. download ejuice me up and you`ll be sortedAll very confusing because he is selling cheap 10ml PG and VG shots at 20mg. You need a chemistry degree for this stuff.
I sometimes think I either don't much like something, or have gone off it - only to rediscover it after a while, and find it's great!I had a little vape of the Blackberry tonight, you know the one I bought 5 bottles of and went off LOL. It wasn't too bad.
Sounds like you may have cross threaded it when putting the top back on. Hitting it with a hammer will make things worseMy FT Nautilus 2 developed a problem and it got worse yesterday.
When I first got it, there was a bit of resistance as I screwed it back together after refilling etc. Then it seemed to right itself, so I put it down to a bit of grit or something similar.
Now it started doing that again, and yesterday, I began noticing a small sliver of silver showing through the join - which should show nothing at all once properly screwed back together.
Closer inspection showed that it's slightly lop sided in that the sliver of silver only seems to show on one side ...almost as though the machined silver metal part of the base where the airflow is has become loose or slightly 'wonky'. I was able to push it down a little, but not to fully level.
It can be screwed tightly together again so that no silver shows, but it takes a stronger grip than I have, and that's not at all satisfactory.
Not sure whether to try tapping the base with a pin hammer to see if it becomes level again -it's very slight, or if it's a waste of time, as it'll no doubt end up the same after a while.
The Nautilus 2 I bought in the UK is still fine.
Looking inside the 'cover' there's not much in the way of threads, but there is a small diagonal nick across them - its always been there though, and what I thought may have caused the same problem I had when I first got it.Sounds like you may have cross threaded it when putting the top back on. Hitting it with a hammer will make things worse
Rarely use IE so don't know what the problem isLooking inside the 'cover' there's not much in the way of threads, but there is a small diagonal nick across them - its always been there though, and what I thought may have caused the same problem I had when I first got it.
Not sure if it can be rethreaded - probably end up being binned I think. It's almost screwing together fully today, so may work intermittently.
_____________________________________
Having a more concerning problem with IE11 - did the two security updates earlier in the month, and it's not allowing websites to work properly ...can't fill in payments on some forms, can't record from Sky via the internet either now.
I've seen things like 'long running scripts' or pages freezing for a while too - shopping at Sainsbury has been extremely slow moving.
Haven't tried uninstalling the updates as I'm not sure it would work anyway ...can't say I've ever done it before, so don't want to screw it up any more than it is.