I went to another vape shop and they are vaping for effects not health.They claim if they puke its good.Mass produced from overseas.
Unless its lab tested stay away from CBD vaping products is my opinion.
I may have to have a friend who has MM certificate get me a vial of lab tested CBD at...
I’ve used kanthal,SS316 and divides.
Dicodes is much more efficient.
I’m using a 0.4phm coil at 245C and it pulls from 14-18watts.
It’s a 11 turn 2mm coil in a skyline rta.
Very close to clouds.
I will continue using dicodes wire.
Battery lasts 2-3 times longer.
I reset counter with new battery...
I have been vaping on dicodes wire now for several days and it’s super easy to set up.
I basically put the coil in,clicked on init,confirm and after tightening up coil leg screws a bit later been vaping on same battery since.
I don’t understand how it works but depending on how long of vapes I...
Sounds good.
I think I have it figured out except the expert mode(s) and I highly doubt I’ll use it unless I get extremely bored.
I
I just ordered some dicodes temp wire and l am curious to see how it vapes.
Thanks
The manual needs a bit of work for it doesn’t say anything about what buttons to push during calibration stages.
I found out it’s the middle button of what increases or decreases values then it says process but screen goes dark before I see any values unless I push power button,then I see...
Once I got a feel for the buttons I can scroll through the menu more easily.
It is simplier than it first looks and over half the menu is display choices or selections that have nothing to do with temperature or power settings.
Ill try SS first with TC and so far I’m using kanthal and SS in...
I think this is the right manual.My menu agrees and it’s better than I expected.
https://www.cremedevape.com/WebRoot/Store/Shops/yxve46fvrnud/5823/07F4/E41D/C318/035F/0A28/1056/5A5E/Dicodes_BF60_manual_preliminary.pdf
RESISTHERM wire is a bit expensive but I’ll give it a try.
What manual did you use?
Did it happen to be this one?
https://www.cremedevape.com/WebRoot/Store/Shops/yxve46fvrnud/5823/07F4/E41D/C318/035F/0A28/1056/5A5E/Dicodes_BF60_manual_preliminary.pdf
The menu scrolling method can get aggravating but I’m all thumbs.
I tried SS and I didn’t see any...
I just got a dicodes by Madbeard mods with 60watt chip.
I’m having problems finding a good tutorial or manual on settings for tempeture control.
I know how to scroll through menus but being used to dna has got me used to graphs to find steady temperatures.
If you know of any tutorials or...
It’s been a while since I’ve been on the forum.
I noticed with FEV some flavors produce the throat hit while others don’t much at all.
HHV NET flavors do and it seems lower nicotine strengths may lessen throat hit.
I’d describe the throat hit as organic taste and cotton brings it out more...
I have used 30Q for vaping and never had a problem but on batteries it’s stamped do not use for vaping or ecig device.
I got VTC4 from same place and they aren’t stamped don’t use for vaping.
I just double checked my devices with older Q30 and I never had any problems with them.
Old 30Q are...
I had some calipers handy and the measurement is 8.5mm on the mesh and mtl coils on the Grimm.
So far the aspire K2 1.6ohm seem to vape better but I have only tried one.
The positive nipple post won’t fit in Grimm so unless you have an old Grimm coil and swap out nipple K2 won’t fit.
What I...
I got some aspire K2 1.6 coils and the air flow for Mtl is much much tighter.
To get coils to work the negative post of coil must be exchanged with an old Grimm coil or it won’t fit properly.
HV basically used aspire coils but a few things so your stuck buying their over priced coils.Greasy.
I realize it’s an old thread and I’ve had no problems with FEV 4.5 but I prefer a wetter or richer vape.
I’ve tried several ways to richen up juice flow but other than enlarging tube holes the amount of juice flowing through seems fixed.I tried 50% pg and still no increase in juice flow...
It feels like it’s one of the orings being a bit too thick and I’m going to tear out orings on the caps and see if it hangs up with no orings so I can rule out threads.
It’s too bad they don’t put knurling or something on kayfun caps because my others can get stuck too at times but the prime is...
Thanks,
I think it should be a decent bf mod given its simplicity and quality components.
I asked for a few pictures of inside components and if it’s like a purge or Frankenskull it should hit hard.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.