voltage drop

Why is it that VV/Spinner eGo batteries have such massive voltage drops. Is it just because they are crappy batteries? I mean, if I set any of my spinner eGos on 4.8v, put it on a meter, it will read anywhere from 4.7v to 4.9v. But as soon as I put a 2.0 ohm load on it, the voltage drop is...

have anyone by any chance used and tested the Rx Machina by wismec ? how much it the voltage drop on it (does it hit hard in comaprison with nudge box mod )? does it still tear 20700 wraps or scratches the batteries ? and for the ones who have it , is there any cons that faced you with it ?

any one got SMPL clones from Fasttech with the snap rings (lock rings) ? if you did please tell your experience with it , how much is the voltage drop on this mechanical mod ? also i would like some recommendations for cheap sub 20$ tube mechanical mods with low voltage drop

Hey folks, this may come a little late for most of you, but here's my review of the Coilmaster 521 Plus tab. You remember, the one that looks like a flying saucer. Points for design ingenuity don't necessarily translate over into performance however. The good news is that you can use the tab...

Hey everyone, I might be a bit late to the game with this review of the Athena squonk kit, but I wanted to take the time to check the voltage drop under load. I used the same methodology as in my investigation of the 521 Plus tab and the "voltage checker". If you're interested, here's the...

OK. Since it was driving me nuts, I tested for voltage drop on 5 of my tube mech mods to get an idea of what I felt was a big difference in voltage drop on the Skyladon. this is in No means a 'scientific' test I cleaned all mods thoroughly before testing. I used the same fully charged Aspire...

Apologies in advance....I am VERY new to mods so I'm having trouble understanding a good bit of info that is out there. I just purchased a Kanger Subox Nano (I was actually one of the unlucky ones that had an Ego blow up on me, scary stuff!). So long story short...I've tried to research...

Question - once in awhile I like to go out with the a Tube mod so I picked up the aspire CF mod. What I don't like about it is the voltage drop as the battery drains. If I were to go get a Tube Mech mod such as the El Diablo would the voltage stay the same throughout the battery life or...

I just built a series dual 18650 box mod. It's unregulated with a MOSFET setup. Without Adam miser it's around 8.5 volts. With a .7 build on it the voltage drops to around 5.9v and steadily drops. I'm using brand-new VTC4 fully charged. Any ideas?

I just built a couple mosfet boxes for co-workers and friends, I've been testing them the last couple days to make sure nothings going to fail before I pass them off. I'm reading .3v and .7v less than the battery voltafe while not underload; I put a voltmeter led display on them and it reads...

I'm thinking about purchasing an smpl amod clone, I would like to know if anyone has experience with them and can let me know which finish has the least voltage drop?

Ok so first off I'm not real new to vaping just to the forum, although I've been lurking for a couple years lol. Anyway I am having the hardest time deciding which mod to get my current one is about to get thrown off a bridge. I get right to it 1. Copper 4nine 2. Copper hades 3. Copper...

Just got my SXK SS clone in the mail. VD is .2V less than my nemesis clone, with a .5 drop on a .09 ohm build. I do like the functionality of this with not having to deal with a locking ring. The groove where the coin slot is located is a little sharp so I'll have to file it a little. I do...

I have a nemesis and stingray x, both clones. I'm not satisfied with the amount of voltage drop I have with them and having learned how a one piece mech is more efficient, can anyone confirm if using conductive glue on the tubing threads will lower the VD? i already cleaned the tubes as best I...

Hi guys wondering if their is anyway to reduce voltage drop on my magneto? I have yet to test my voltage drop, I am going to get a multimeter this weekend and test it. I'm running a .3 ohm build with a plume veil and have it wide open and not producing the vape amount I should be. Any suggestions?

Hello all, Does the Smoktech Omnitester replace a multimeter for use on an unregulated mechanical mod (no kick or kick2)? I know it will measure the resistance of the coil. I know it will measure the voltage output of the battery. I know it will measure the voltage drop when coil and battery...

Hi everyone. Got my Sigelei 20W in the mail today and I absolutely love it. For some reason mine didn't come with an instruction manual, and the one online is in pretty broken English. My question has to do with the battery voltage drop on my display. I know that under load some battery drop is...

also, air-holes on both sides, low walls on the well Can't seem to find anything, or at least not anything that tells me so. Just seems so silly to have high-quality connections on the mod and then put a dripper with a SS post on it. [ended up getting THIS ]

Are there appreciable differences when looking at Brass/SS/Copper body metals? If so, Which does better? Also: is there a difference when using mixed vs uniform metals? Not aesthetics. Performance. Voltage drop, battery life, etc.

So I've been hearing a lot about voltage drop and how hard this mod hits vs. that, I have many mods, authentic and clones, so I started measuring the voltage with an accurate Fluke multimeter, first I measure the battery voltage using the positive and negative terminals, then I load the same...