26650 Battery Contender 50A continuous(?!?!!?)

Discussion in 'Battery Mods' started by awj03130, Feb 2, 2014.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. awj03130

    awj03130 Senior Member Verified Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Overland Park, Kansas, United States
    How can we get some of these? 50 amp continuous and 120 amp burst?!??!??

    I smell a group buy.....

    [​IMG]

    Sent from HAL 2000 using Tapatalk
     

    Attached Files:

  2. Jimi D.

    Jimi D. ECF Guru ECF Veteran

    Joined:
    Oct 26, 2010
    Location:
    Florida Keys
    Sweet Jesus !!!!
     
  3. Jimi D.

    Jimi D. ECF Guru ECF Veteran

    Joined:
    Oct 26, 2010
    Location:
    Florida Keys
    Only one thing though. The voltage is 3.2
     
  4. bapgood

    bapgood Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Apr 16, 2012
    Location:
    Utah
    Yeah A123 cells are actually pretty good cells but the voltage is lower so it won't work with most regulated mods.

    What is the mAh? Having a hard time reading the data sheet on my phone.
     
  5. Jimi D.

    Jimi D. ECF Guru ECF Veteran

    Joined:
    Oct 26, 2010
    Location:
    Florida Keys
  6. awj03130

    awj03130 Senior Member Verified Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Overland Park, Kansas, United States
    Well, my dreams are crushed.... If only it was 3.7 volt....

    Sent from HAL 2000 using Tapatalk
     
  7. dr g

    dr g Moved On Verified Member ECF Veteran

    Joined:
    Mar 12, 2012
    Location:
    Paradise
    2500mah ... there goes the reason for the larger battery
     
  8. awj03130

    awj03130 Senior Member Verified Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Overland Park, Kansas, United States
    I thought it was usually a trade-off between mAh and C rating...

    The reason for sub-ohmers like myself would be to stick it in a 26650 mech and run a .07 ohm coil well within the battery's continuous max discharge rating......

    That being said, after doing the math, you would be vaping at 146 watts... And 46 amps if you did a .07ohm build. I'm ordering these. :)

    Sent from HAL 2000 using Tapatalk
     
  9. retird

    retird Vaping Master Verified Member ECF Veteran

    Joined:
    Dec 31, 2010
    Location:
    North Side
    Make sure to use the proper charger........
     
  10. awj03130

    awj03130 Senior Member Verified Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Overland Park, Kansas, United States
    Was lookin at that. Probably going to purchase a LiFePO4 charger and separate it in the house so nothing... Gulp.... Happens


    On second thought, if I were to run a quad 6 wrap quad micro coil and the current 28AWG setup nets me .16-.18 ohms (depending on ID).... What gauge wire would I need to get the ohmage down to .07?

    Anyone know where I can get 2 gauge A-1 kanthal?

    Sent from HAL 2000 using Tapatalk
     
  11. retird

    retird Vaping Master Verified Member ECF Veteran

    Joined:
    Dec 31, 2010
    Location:
    North Side
    What overcurrent/short circuit protection are you going to use in your mechanical mod ? A proper charger is not the only thing to pay attention to.......
     
  12. awj03130

    awj03130 Senior Member Verified Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Overland Park, Kansas, United States
    Not sure what you mean... Short protection? on a mech?

    Not touching legs to base/cap/other legs?

    Over current protection? Not building a .0000001 ohm coil on an ICR battery?


    If I'm missing something big, please help me here... Don't really want to blow up.

    Sent from HAL 2000 using Tapatalk
     
Thread Status:
Not open for further replies.

Share This Page