Azeroth CoilArt by CoilTech

[Quantum Mech]

For those that have been luving the Limitless+ this is very similar

Room to make wider coils & way more air flow that can be directed over the whole coil

1st build is chugging along nicely & settled in at 90w

SS316 24wraps of 24awg @ 3mm id

 

[whiteowl84]

I asked this in another thread when you mentioned it.
Are the screws long enough for big wires?
That's the only reason I bought a limitless.
I love the genny/goon thing it has going on.
I'd appreciate if you could give a 1-10 rating for build quality and anything else you can think of. I love the looks of it.

 

[SLIPPY_EEL]

Looks like its built well and your coils aren't bad either i bet it guzzles the juice.

I'm not 100% certain i think it might have been for a whole new limitless that i saw that you can change the deck as in the configuration of the posts and they even had a deck like this one, goon style clamps, it looks cool, i was almost getting one but im getting better at resisting the urge, just have to keep telling myself that something better is always around the corner , that Azeroth has some quality going for it though.

 

[Quantum Mech]

I asked this in another thread when you mentioned it.
Are the screws long enough for big wires?
That's the only reason I bought a limitless.
I love the genny/goon thing it has going on.
I'd appreciate if you could give a 1-10 rating for build quality and anything else you can think of. I love the looks of it.

yes if you compare these pics, the wire used is 24awg so should give a good idea

although monster coils will need longer screws, the azeroth air flow would be better with the 3x 45degree afc slots

build wise its very good, no sharp edges and push fit of glass/top cap are just right, tight but not too tight, posts are rock solid and I seem to be able to nip the wire tighter with clamps

time will tell how the gold plating holds up

 

[Quantum Mech]

Looks like its built well and your coils aren't bad either i bet it guzzles the juice.

I'm not 100% certain i think it might have been for a whole new limitless that i saw that you can change the deck as in the configuration of the posts and they even had a deck like this one, goon style clamps, it looks cool, i was almost getting one but im getting better at resisting the urge, just have to keep telling myself that something better is always around the corner , that Azeroth has some quality going for it though.

yeah as with any over used new tank its guzzling plenty

the positive post fits into a slot but the negative can be adjusted

 

[whiteowl84]

Are they m2.5 or m3.5 threaded?
If I order the tank tomorrow, I'd like to have the screws ordered as well.
I'm sure that I could fit my wire in it but if it has the room to go crazy, I'd hit a wall fast.

 

[Quantum Mech]

sorry mate, best can do as battery gone in calipers

 

[Torturedzen]

I just rec'd my Azeroth, was browsing threads with that topic and saw this one. Have you or anyone else found their top cap to be just a wee bit loose fitting? I mean not loose loose, but on mine it requires pretty much zero effort to pull off, which could be remedied by a thicker o-ring. My concern is I've noticed small amounts of juice accumulating a little too easily around the fill port and dribbling down the outside with the top cap in place.

 

[Quantum Mech]

mines tight, can hold the weight of an RX200 easily

 

[Parth]

mines tight, can hold the weight of an RX200 easily

View attachment 611801

Hey guys,
I bought mine over the weekend and for the life of me I can't get it to fire . I have .43 ohm coils I use with my Cleito rta with no issue, but it shows short/check atomizer on my HCIGAR 75. Same with the coil art .36 prebuilt coils. Is there anything I should look at doing? I've already checked the 510 connection, unscrewed and rewick screw with it firm and loose, same outcome. All 4 posts are firmly screwed in, and the leads are either side by side or are overlapping. Any suggestions?

Sent from my SM-G935V using Tapatalk

 

[whiteowl84]

Does it say short with no coil?
Also my vt133s both say that for no reason at all. Both are dead. Make sure it's not the mod.
HCigar uses a daughter board. I wish I had known that before purchasing.

Other wise tear the atomizer down and see why it's shorting and fix it.

 

[Parth]

I've tried multiple coils with different types resistances. The weird thing is I used the same 2 coils I use in my Cleito rta and still shows a short. My guess is the connector pin, insulator or or possibly the ends of the coils touching each other?

Sent from my SM-G935V using Tapatalk

 

[Parth]

Does it say short with no coil?
Also my vt133s both say that for no reason at all. Both are dead. Make sure it's not the mod.
HCigar uses a daughter board. I wish I had known that before purchasing.

Other wise tear the atomizer down and see why it's shorting and fix it.

I did find something while reading the manual/techspecs for mine. It says to screw down the cathode screw of the vt75 displays short/check atty. Going to try that tomorrow, hopefully that fixes it haha.

Sent from my SM-G935V using Tapatalk