I see little droplets literally from under the metal cap where it meets the top of the bottle. It doesn't appear to be at the top of the cap where it meets the tube. Is this normal? Will a new tube fix that?
I see little droplets literally from under the metal cap where it meets the top of the bottle. It doesn't appear to be at the top of the cap where it meets the tube. Is this normal? Will a new tube fix that?
I see little droplets literally from under the metal cap where it meets the top of the bottle. It doesn't appear to be at the top of the cap where it meets the tube. Is this normal? Will a new tube fix that?
I get that as well on the one ive been using for like a week now. Prob not getting a 100% seal on the cap threads.
No big deal to me though atm. Not like it's spewing out or any puddle under the bottle.
Can anyone post a link to videos of the new bottle seating procedure, I haven't seen any yetEmptying the bottle and going back over the "seating" procedure in the video had those two sorted out with no more issues
thanks hun. derrrrr I saw the add a higher number for another meter, but just got confuse and thought it started with 4 meters. heheheThat is the OD and ID (diameter), they sell it by the Meter...Quanity 1=1 Meter
same here. I was thinking perhaps I need to do like element says in the quote below and redo the "seating" procedure, but have been busy and lazy and haven't done it. The old bottle was leaking some on 2 mods before I got these, the mini with old bottle was leaking a LOT, puddle under the mod, not just the bottle. Still haven't dealt with that one. lolMine does have a puddle under the bottle. And somehow the back of the door is wet.
Jup think I need to do thisOn two others I had some leaking at the cap and bottle. Emptying the bottle and going back over the "seating" procedure in the video had those two sorted out with no more issues.
Good info, thanks.I had better luck filling my bottles with hot water before doing the squeeze to seat the cap. You can see when it stops dribbling. Took me a few squeezes to get it to stop leaking.
Leaking, puddling original bottles? Hmmm. Have never seen that, no leaks of any kind from the original 3ml or 6ml bottles/caps themselves. And I squonk them nearly dry. Maybe a squonk style issue? I don't fill the bottles to the top, leave liquid displacement room for the feed tube and a small air space. And just snug the cap, a learned touchy-feely thing so it's tight enough to seal against the o-ring without compressing it much. Then I use a long, controlled squonk in, same out to compensate for the differences between each atty's ability to take and drain liquid. I don't feel the need to force the squonk, and it doesn't tighten up as the bottle empties unless I snugged the cap a little too tight. I use 2.5/3.0mm form coils mostly now with pulled/rolled cotton wicking that holds a lot more liquid so I squonk less often.
Occasional leaks at the feed tube to older 510 nipples yes, when a feed tube had been off and on enough times to loosen up some (I didn't glue them). But I also didn't take the feed tubes off very often. Leaks at the new 510 nipple to 510 tube yes. Strange maybe, but all of them have leaked from the start or eventually in the new small Reos where they never have in the Grands. An easy fix though with TFE Paste and making sure the nipples are just snug enough that the positive contact will not move. They are a huge improvement that Rob came up with, but a little finesse messing with them always goes a long ways.
The original bottles are working just fine for me, and I have a huge stockpile of them because they are not needing replacement very often. The extra capacity would be nice, but where I want it the most is in the 3ml bottle Reos. I didn't say "need" because my 30ml needle tip/dropper refill bottles are always close at hand. But I drain the smaller bottles pretty fast with my LDLH's, and just one shy of half of my Reos use the 3ml bottles. Sometimes the need to refill them comes at a less than favorable time.
When I place an order for something else I'll still add some of the Italia 8.5ml bottles to it to try out though. And I'll keep watching for larger capacity bottles for the smaller Reos that would work hassle free. The 24 square 6ml soy sauce bottles I bought very early on in my Reo experience didn't live up to that, so they are not used.
All just details. When all you vape is Reo gear your vaping life is supreme, as easy as it gets.