Cleaning/Washing 316 SS tubes

Discussion in 'E-Cigarette Maintenance' started by NerdVap0r, Feb 8, 2014.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. NerdVap0r

    NerdVap0r Super Member Verified Member ECF Veteran

    Joined:
    Jan 12, 2014
    Location:
    Bay Area
    So i just bought a hcigar nemesis & wondering the best way to clean 316 SS tubes while avoiding long tern rust. Is it as easy as just rinsing in warm water & letting it air dry? thx
     
  2. State O' Flux

    State O' Flux Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 17, 2013
    Location:
    Seattle
    This is going to seem complicated and obsessive - actually takes less time to do than it took to write this little "guide".

    Cleaning with warm soapy water works nicely to remove the usual "stuff" that collects on mechs. Dry with compressed air (compressor or computer blast cans) or just soft cotton toweling. Some prefer to use nothing but 99% IPA... which I have no issues with if that's your preference.
    If the contacts have a bit of corrosion, that can be gently removed with a fine scotchbrite pad, equally fine stainless steel wool or sponge - or 1000 grit or finer wet/dry sandpaper. Rinse cleaning residue with 99% IPA.

    Although I prefer MG Silver grease on electrical contacts and even threads (link for tech reference - buy from Amazon - it's cheaper) - it can be a bit expensive for some - so what ever your preferred anti-corrosion electrical grease - Noalox, Ox-Gard, NO OX ID A and so on. Bare, clean SS works just peachy too.

    If it's bare, polished SS, you may re-polish it with any common metal polish - Mother's, Simichrome, Nevr-Dull - what ever you like - to maintain the finish. Some polishes will leave a protective residue... which in most cases IMO, isn't all that protective.

    Finish with a few light coats of (specifically) Renaissance Micro-Crystalline Wax to all exterior surfaces (read up on this and you'll understand why it's preferred by so many) - work it in with your fingers then buff lightly to remove residue, using an "extra soft" toothbrush for grooves/crevices and engravings.

    Make sure there is no water remaining inside prior to installing a battery. ;)
     
  3. NerdVap0r

    NerdVap0r Super Member Verified Member ECF Veteran

    Joined:
    Jan 12, 2014
    Location:
    Bay Area
    Thx, nice write up :).

    As for just warm water and soap, what ingredients should i avoid?
     
  4. stevegmu

    stevegmu ECF Guru ECF Veteran

    Joined:
    May 10, 2013
    Location:
    6992 kilometers from home...
    According to their website it is stainless. If it were 316 stainless, it would be advertised as such. 316 stainless is very resistant to corrosion and rust. Under normal conditions, it should never rust. 304, not so much...
     
  5. State O' Flux

    State O' Flux Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 17, 2013
    Location:
    Seattle
    Unless we need to call the bomb squad or DEA on you [​IMG]... it's unlikely there's anything under your kitchen sink that will do damage to SS.

    Dish soap, Simple Green, Orange Clean or OxyClean and warm/hot water... any of those will be fine. :)
     
  6. NerdVap0r

    NerdVap0r Super Member Verified Member ECF Veteran

    Joined:
    Jan 12, 2014
    Location:
    Bay Area
    Thx folks. i see, guess the Chna nemmy thread was false on the 316 SS steel. I'll just rinse & scrub with warm water for now. Everythng soap i have at home has chloride which i read was very bad to steel.
     
  7. Charon

    Charon Senior Member ECF Veteran

    Joined:
    Feb 4, 2014
    Location:
    Indiana
    Dawn dish soap is fine on stainless, either 309 or 316.
     
  8. Cazan

    Cazan Full Member

    Joined:
    Mar 16, 2010
    Location:
    Pueblo, CO.
    Seems soap, water & air- All plentiful and cheap-should do fine. If you get something that this won't clean on SS, I'd wonder some...? Lots of material nowhere near as rugged says to clean with 'mild detergent', so I'd think you're overthinking a bit. I think. Or am I overthinking?? Hafta think about that one. Cazan
     
  9. Dj Xy

    Dj Xy I'm winning like Charlie Verified Member ECF Veteran

    Joined:
    Feb 5, 2011
    Location:
    baltimore, maryland
  10. scscheib

    scscheib Senior Member Verified Member ECF Veteran

    Joined:
    Feb 11, 2014
    Location:
    Pittsburgh,PA,USA
    I have a big can of Cape Cod that I use as well. Just be careful and don't use it on anything that you don't want removed such as painted writing, glare proofing agents etc. This stuff is pretty strong and will remove scratches and sometimes stuff that you don't want it to, lol. I wasn't all that experienced with it and it removed the glare proofing on one of my watches sapphire, which isn't easy to remove.


     
Thread Status:
Not open for further replies.

Share This Page