Genesis Atomizer Tank

Discussion in 'Tank Mods' started by mrengles, Aug 27, 2011.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    I know this info is on ECF, so much in fact it makes it hard to search.

    I've missed out on the co-ops and really want to get my hands on a Genesis Atomizer Tank.

    Can someone point me to some open source drawing/specs so I can have a shop build (turn) a few for personal use?

    I've used www.emachineshop.com before and would probably use them again.

    Any other info you can provide would be awesome.

    I did find some info on the Will Pro 13 and 7, but have a tough time translating for obvious reasons (I can only read/write English and google dose a poor job). Has anyone used or owned one? How do you like it?

    I don't like the fact that it can only be used with an ego. I guess that could be changed since I'm going to draft them myself.

    Thanks everyone. Next time I'll be sure to jump in on the community build!

    -Mrengles
     
  2. solarisx

    solarisx Full Member

    Joined:
    Sep 7, 2010
    Location:
    Cali
    Why don't you use the emachineshop design software?
     
  3. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    I'm going to... :)
     
  4. otrem

    otrem Super Member ECF Veteran

    Joined:
    Feb 22, 2011
    Location:
    Yosikadiri, Philippines
    read 'Scubagen mods'.
     
  5. Scubabatdan

    Scubabatdan Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 14, 2009
    Location:
    Dothan, AL
  6. sierra22

    sierra22 Moved On

    Joined:
    Jun 11, 2011
    Location:
    USA
    there is 4 of them for sale in the classies for 120. better hurry up!
     
  7. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Thanks!!!!!
     
  8. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    I found some specs and drawings on the ULRA 18650 also, I'm going to try and work something up this weekend...

    I plan on using a little bit from each design, the ScubaGEN, WillPro13, and ULRA. Wish me luck. :)

    Hopefully I'll be able to come up with a 6-8 ML Genisis Atomizer Tank. (That works, if not I'll have some fun working on it...)

    Thanks again Dan!
     
  9. otrem

    otrem Super Member ECF Veteran

    Joined:
    Feb 22, 2011
    Location:
    Yosikadiri, Philippines
    update us wd pics and vapes later.
     
  10. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Will do...
     
  11. NatureBoy

    NatureBoy Ultra Member Verified Member ECF Veteran

    Joined:
    Jan 21, 2010
    Location:
    Toronto, ON, Canada
    The ULRA is one I would have liked to purchase, but it never went into production...
     
  12. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    I'm only looking to use some design aspects of the ULRA tank/atty not the circuitry.
     
  13. NatureBoy

    NatureBoy Ultra Member Verified Member ECF Veteran

    Joined:
    Jan 21, 2010
    Location:
    Toronto, ON, Canada
    Yeah, that's actually what I meant... the circuitry wasn't something I was interested in. I just liked the tank/battery tube combo. Some Genisis attys are just too ridiculously big.
     
  14. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Here are some photo's of what I worked on over the weekend. This unit is about 10MM shorter in the tank area then the ScubaGENv3.
     

    Attached Files:

  15. Scubabatdan

    Scubabatdan Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 14, 2009
    Location:
    Dothan, AL
    Just a suggestion, Since you are going with a single wick, I would make the electrical connectors as close to the wick as possible. Cuts down on glowing kanthal :)
    I.E.
    Reduced holes.jpg
    Dan
     
  16. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Thanks Dan.

    Another forum member is selling me one of your ScubaGENv3's for cost. Look forward to trying it out.
     
  17. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Dan,

    Have you ever made one of these from AC aluminum? How did it hold up? Turning stainless might be a little problem for me. I don't have access to the right tools for a prototype.
     
  18. Scubabatdan

    Scubabatdan Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 14, 2009
    Location:
    Dothan, AL
    Still using the one I turned from aluminum, holds up great.
    Dan
     
  19. mrengles

    mrengles Super Member ECF Veteran

    Joined:
    Apr 21, 2011
    Location:
    Boca Raton, FL USA
    Here are some new drawings, I've threaded the fill hole, so it can be closed with a M3 screw. The POS/NEG taps are also M3 threaded. I'm still deciding on how to wire, I might come straight up from the atty POS, and use a filler plug on one of the taps, otherwise I have some high temp nylon standoffs at my office. (My family has small military/aircraft electronics biz)

    Let me know what you think.
     

    Attached Files:

  20. silentt

    silentt Vaping Master Verified Member ECF Veteran

    Joined:
    Feb 14, 2011
    Location:
    Virginia
    I still haven't done anything with my scubagen3 that Dan sent. I'm too lazy but I will try to build it soon. I wish I could have someone build it for me lol

    I'm probably missing a really delightful and epic vape.
     
Thread Status:
Not open for further replies.

Share This Page