I cannot build anything
- Thread starter gel drops
- Start date
- th_trl_thread_readers 0
-
- Tags
- kayfun burning
- Status
Can you see my ocd tendencies in my coils? 
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
I will trade ya...mine is having to buy a new device every week and then don't open it for about 2 or 3 weeks makes no sense Lol.Can you see my ocd tendencies in my coils?
Sent with one hand, the other is busy vaping.
With an ipv mini 2, ZNA50 and a variant, I'm all set till one of those goes out
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
Wow..about 5 wraps using 26 gauge K,3/32 DB.Put me at around .9 ohms,that seems to be my sweet spot when it comes to rebuilding the heads of my subtanks.Japanese cotton I like it.
Did some work on my ipv mini 2.....what do ya think?
The top is actually polished as well... The shadowing makes it look black
Sent with one hand, the other is busy vaping.
The top is actually polished as well... The shadowing makes it look black
Sent with one hand, the other is busy vaping.
The top is actually polished as well... The shadowing makes it look black
Sent with one hand, the other is busy vaping.[/QUOTE]I wished mine looked like that how long did it take you to do it ?
I've got about 3 hours into it so far
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
Be careful,you might get flooded with PM's people will be wanting to send there mini to you to fix it up for them!
First build on the geyser. I just couldn't bring myself to do a quad build. Ended up being .6 ohm. Only my third build ever, the other two being on a doge v2. I don't think it's two bad. Pretty good flavor.
First build on the geyser. I just couldn't bring myself to do a quad build. Ended up being .6 ohm. Only my third build ever, the other two being on a doge v2. I don't think it's two bad. Pretty good flavor.
The coils look ok, but you have too much cotton in there!
All you need is enough wick tail to reach the deck and tuck in under the coil a bit. Cut down the cotton and your airflow will improve
I'm going to break out the Magma,very deep juice wells.I only have two RDA's,Magma was actually my very first rebuildable Atty,subtanks is basically all I have been using,only takes about less than 5 minutes to rebuild the heads on them,on the flip side however they have made me extremely lazy!
Nothing wrong with a tried and true micro/macro coil. They have a selling point of simplicity
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
I totally agree,yes was insinuating the one that I had on there had a hot leg so to speak.Nothing wrong with a tried and true micro/macro coil. They have a selling point of simplicity
Sent with one hand, the other is busy vaping.
Here's my newest build....
26 gauge twisted, sleeper coil (the post holes in that atty are quite large, so I didn't have to do sleeper coil style, but I find they heat more evenly for me). 6 wraps per coil, .2 ohms
And check out that airflow
Sent with one hand, the other is busy vaping.
26 gauge twisted, sleeper coil (the post holes in that atty are quite large, so I didn't have to do sleeper coil style, but I find they heat more evenly for me). 6 wraps per coil, .2 ohms
And check out that airflow
Sent with one hand, the other is busy vaping.
I prefer direct lung hits,what atty is that^..with that much air flow do you think a direct lung hit might be an issue..I'm sure the air flow is adjustable.
Last edited:
It's the airek.... And it's perfect for lung hits, and you can flip the cap for smaller air holes, but for lung hits I like the air wide open
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
- Status
Similar threads
