Kick problems with roller, 69 mod or Gus telescope

Discussion in 'New Members Forum' started by wwaaazzup, Jan 26, 2013.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. wwaaazzup

    wwaaazzup Moved On

    Joined:
    Dec 1, 2012
    Is anyone having problems with a kicked telescoping mod? What would be better to by when using a kick... Roller, 69 mod, or the Gus?
     
  2. Caridwen

    Caridwen ECF Moderator Senior Moderator Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 15, 2011
    Sorry, I don't know the answer. Just wanted to bump this for you in case someone else does.

    After you have 5 posts you can post in the APV forum- you might get more help there.
     
  3. wwaaazzup

    wwaaazzup Moved On

    Joined:
    Dec 1, 2012
    This is an update as to what's been going on with my Roller by Atmizoo with.a kick in it. Brand new aw imr 18490 and a brand new kick. Basically the kick is shutting me down after only an hour and a half. When that happens if I twist the bottom of the roller a bit then it works for a minute but when I set it down and pick it up ten minutes later its shut off again or doing the sputtering thing again. I can take the kick and the battery out of the Roller and put them in my Legacy from PURESMOKER and it will work just fine for 4 more hours. I've done everything possible to make it work in the roller consistanly but so far I still have to loosen the bottom then tighten it again to make it work. And I REALLY have tried everything.
    I'm just posting.g this in case anyone is having the same problem as I am.
     
  4. BillyBenchpress

    BillyBenchpress Senior Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Dec 5, 2012
    Location:
    Pendleton, Oregon USA
    I am having the same issues with my kicked Smoktek Telescope. I think that there is some kind of conductive lube that people use, but the name is escaping me at the moment. You just a drop or two to either side of the kick and it increases conductivity



    Sent from my Galaxy Nexus using Tapatalk 2
     
  5. BillyBenchpress

    BillyBenchpress Senior Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Dec 5, 2012
    Location:
    Pendleton, Oregon USA
    Found it.... NOALOX. It's made for pressure sealed wire conduction. It's also an anti oxidant.

    Sent from my Galaxy Nexus using Tapatalk 2
     
  6. wwaaazzup

    wwaaazzup Moved On

    Joined:
    Dec 1, 2012
    Also I took some tape and cut it to put on the opposite side of the spring on the kick. It made the kick fit a little tighter and helped a little.
     
  7. BillyBenchpress

    BillyBenchpress Senior Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Dec 5, 2012
    Location:
    Pendleton, Oregon USA
    Just got my 69 mod out of the mail 10 minutes ago. Kicked it. So far none of the problems i was experiencing with the Smoktek Telescope. Kick actually fits a bit tighter in the 69. So far so good. Glad to hear that the tape worked for ya

    Edit a word
     
  8. wwaaazzup

    wwaaazzup Moved On

    Joined:
    Dec 1, 2012
    Cool. If you have any issues with the 69 mod and the kick let me know because I want to order one in a couple of weeks.
     
  9. wwaaazzup

    wwaaazzup Moved On

    Joined:
    Dec 1, 2012
    Newest update to my findings with my roller and the kick. I posted earlier that it was the kick but since then I started having that problem again. I'll make it short... it was really the hot spring. Easy fix... go to Altsmoke and order the hot spring for the silver bullet. It fits perfectly and instantly fixed all issues. I ordered 2 so I would have a spare. Order it, trust me. I got into gennys and it made a world of difference and fixed ALL voltage drops.
     
  10. greener85

    greener85 Full Member Verified Member

    Joined:
    Jan 5, 2012
    Location:
    Charlotte, North Carolina, United States
    was the only issue you were having with the Roller was kicking it? I just got a roller for Genesis atties I just got also.

    Did replacing the spring fix anything else you saw as an issue?

    I did see that AtmiZoo has a kick cyclinder for purchase on their site for the roller / dingo.
     
  11. edenlaa

    edenlaa Full Member

    Joined:
    Dec 10, 2012
    Location:
    kuala lumpur
    remove the kick. and try to find genesis atty. try to set up with lower ohm. u can feel better than use kick.
     
: altsmoke, smoktek
Thread Status:
Not open for further replies.

Share This Page