Mark-T Infinity Atomizer

Discussion in 'Modder/Accessories Supplier Forum' started by mark78, Aug 9, 2011.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    New Image1.jpg

    Hello to all,

    Tired of conventional atomizer, i've tried to make one indestructible atty.
    Some details about my Mark-T Infinity Atomizer
    -new 510 conection,made from O
    -midle piece for dripping
    -midle piece for tank cartridge
    -drip tip
    -cone for ego battery

    I use genuine eGoT wick material,pre-round.
    All is made from SS
     
  2. Odell

    Odell Super Member ECF Veteran

    Supporting member
    Joined:
    Aug 25, 2010
    Location:
    Ocala, Florida
    That looks really nice Mark. Tell us more!
     
  3. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    More picture: ImageShack Album - 22 images
    222.jpg
    In this picture is genuine wick material from eGo, all is pre-round, i use for atty wire 0,12/0,13 and 0,15mm.
    No burn taste,no nasty taste, clouds of vapour:vapor:
     
  4. arunce

    arunce Full Member

    Joined:
    Jul 21, 2010
    Location:
    Portugal
    Nice atty. Where did you get the "ego wick"?
     
  5. Lazrah

    Lazrah Senior Member ECF Veteran

    Joined:
    Jun 29, 2011
    Location:
    Juneau,AK
    wow those PV parts in your Photo album are enormous!! they make the runway look small lol.. seriously tho, Nice work! looks nice.
     
  6. Lambch3p

    Lambch3p Super Member ECF Veteran

    Joined:
    Mar 5, 2011
    Location:
    Sunny Tampa Florida
    That is a great looking tank atty! Its very sleek and compact, which I like. It totally looks like something I would love to have. :)Great work! I too am curious where you got the ego wicking from?
     
  7. jmarkus

    jmarkus Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 3, 2011
    Location:
    CA USA
    looks alot like the a2-t. very nice with the shiny parts...how much $ will this be and when will it be available?
     
  8. executivul

    executivul Senior Member ECF Veteran

    Joined:
    Mar 5, 2011
    Location:
    Romania
    Hello,
    I am the lucky owner of such an atomizer from Mark. It works great, far better than any other repairable attys I've tried, the build quality is astonishing, it's all made out of stainless steel, all parts fit perfectly.
    The heating element has the coil wrapped around silica from the factory, that means equally spaced wire, I was never able to wrap by hand more than 4-5 wraps for my repairable attys, with this material I've put 7 wraps of wire, having 3.2 Ohms and that is just great at 4.4V on my Provari.
    As TH it's a 5/5, flavor 5/5, steam quantity 4.9/5 because I tend to overdrip a little, and this atty having the air hole to the side and no coil cup needs only 1-2 drops at a time.
    Did I mention it came with a SS drip tip?
    One happy camper here.
    Thank you Mark.
     
  9. blondie1964

    blondie1964 Super Member Verified Member ECF Veteran

    Joined:
    Dec 29, 2009
    Location:
    Pittsburgh
    Where do I order! so cool, let me know :)
     
  10. BigBulli

    BigBulli Super Member ECF Veteran

    Joined:
    Apr 24, 2011
    Location:
    N/A
    This looks A LOT like the Bulli A2-t, only difference I see is the wick. Is there something I'm missing? Even the three rings and shape look identical.

    It looks like the knurling on an A2-t was ground down than was polished to nice finish.
     
  11. breaktru

    breaktru Vaping Master Verified Member ECF Veteran

    Joined:
    Jul 30, 2010
    Location:
    Most Southernly part of New York State
    Sure looks nice
     
  12. speedemon

    speedemon Ultra Member Verified Member ECF Veteran

    Joined:
    Nov 7, 2009
    Location:
    Chicagoland
    Looks nice would like to have one of those bad boys!
     
  13. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania

    The main difference between my atomizer and others atomizer, is that everything is built from 0, including the 510 connector ,is designed and made from O.
    And it is very small, take a look at the picture!!
    It is not polished!! This is special stainless steel, i use the best material on the market for Mark-T
    I do not use any part of the Chinese atomizers, except wick material.

    It's like comparing a Boeing 737 :vapor: with an ATR:laugh:
     
  14. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    PV parts is my Boeing 737, and runway is for my airplain:thumbs:
     
  15. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    Can I keep the secret!?!;-)
     
  16. BigBulli

    BigBulli Super Member ECF Veteran

    Joined:
    Apr 24, 2011
    Location:
    N/A
    Just saying it's been done before, in stainless steel as well:
    Bulli-Smoker A2 - Bulli-Smoker
     
  17. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    I release my first prototype of Mark-T on 23/05/2011 :vapor:, and i see A2 is release on 16/06:confused:
     
  18. BigBulli

    BigBulli Super Member ECF Veteran

    Joined:
    Apr 24, 2011
    Location:
    N/A
    I don't know when you released yours but if you did when you say you did Bulli had an A2 much longer than that and added the tank to the product line.
     
  19. mark78

    mark78 Registered Supplier ECF Veteran

    Joined:
    Mar 11, 2010
    Location:
    Bucharest Romania
    There are 2 difrent products.Let's move on.:vapor:
     
  20. executivul

    executivul Senior Member ECF Veteran

    Joined:
    Mar 5, 2011
    Location:
    Romania
    It's a different beast, the A2. The A2 Tank has 3 parts: the base with the coil, the middle needle part, and the top sleeve which holds the cart. The Mark Tank has only two parts: the base with the coil and the sleeve which has the needle and holds the cart. The third part you see it's just a 1/2" cone/cover for the ego battery's outer threading, so just for looks, otherwise the atty itself has only 2 parts, and that makes it much smaller than the A2.
    By the way the base idea is "self service atomizer" and it's been floating arround for some time, the russians at ecigtalk.ru have at least a half dozen models, some made from 0 (zero, scratch) from a RCA sound connector, some using parts from different types of chinese attys, so all these are just implementations of the base idea which honestly I dont't know who belongs to.
    Regards.


    Sent from my iPad using Tapatalk.
     
Thread Status:
Not open for further replies.

Share This Page