Mike n Tibs DNA Mods!

[bapgood]

I have the coop fuses... those no good?

sent by my mind.

Remind what they were? They should be fine, I think Mike recommended leaded ones that are easier to solder.

 

[kamil99]

I think they are 9a. Not at home right now to check.

sent by my mind.

Edit: 9a/15a trip
http://www.mouser.com/Search/m_ProductDetail.aspx?R=RGEF900virtualkey65000000virtualkey650-RGEF900

 

[tiburonfirst]

these are the 9amp

https://www.mouser.com/Search/ProductDetail.aspx?R=RGEF900virtualkey65000000virtualkey650-RGEF900

all parts used are in the first post with links to the actual items
http://www.e-cigarette-forum.com/fo...s-ends-switches-contacts-fuses-etc-co-op.html

 

[tiburonfirst]

Better grab the links them

easier to put them in my shopping cart

 

[mamu]

Here's a great deal on Littelfuse 3A smd fuse that a member posted in my Arlo thread - only 20¢ each and is the exact same fuse digikey sells for $1.86 each.

50 Pcs Littelfuse PolySwitch SMD PTC Resettable Fuses 1812 3A 6V 1812L300MR | eBay

 

[Texaslimo]

What mod or what kind of adjustment?

It is a Panzer. Both top and bottom are screw type adjustments.

 

[tiburonfirst]

I think they are 9a. Not at home right now to check.

sent by my mind.

Edit: 9a/15a trip
RGEF900 TE Connectivity / Raychem | Mouser

pretty sure they were chosen with the tibs in mind - bumping this up for either mike or bap to comment

 

[mikepetro]

pretty sure they were chosen with the tibs in mind - bumping this up for either mike or bap to comment

Yes, you need at least a 12A hold total for a DNA30. Two of these n parallel is 18A and would work fine, I think they were best we could find at the time.

Since then I found and bought a handful of the 16R600GU 6A
16R600GU Littelfuse | Mouser

I also bought some of the 7A SMD fuses that Bap mentioned.

 

[bapgood]

It is a Panzer. Both top and bottom are screw type adjustments.

If you have room you could try springs under the contacts like the TGT 510 center pin.

 

[mikepetro]

Tibs2 Beta tester, Lipo model:

 

[bapgood]

Tibs mod lipo version

Turnigy A-spec Nanotech 6000mah 65-130C

This is polished alumide case with clear gloss polyurethane, the buttons are black detail.

 

[TS12000]

Hey Bap, do you know the dimensions of that batt uncased offhand?

 

[bapgood]

Close to these....I thinks I got the height down to 3.125"

 

[Proetus]

Nicely done gentlemen!

 

[bapgood]

Close to these....I thinks I got the height down to 3.125"

lol....I meant to post this pic as well

 

[TS12000]

lol....I meant to post this pic as well

Lol, thanks bap. Got some coming one way or the other.

 

[iminuvaping]

Very nice Bap,
I would have gone with that battery myself but the 5600 was the biggest i could find at the time with minimal modification.
I just didn't think i was ready to start messing with the 7.4V lipos...

 

[bapgood]

Very nice Bap,
I would have gone with that battery myself but the 5600 was the biggest i could find at the time with minimal modification.
I just didn't think i was ready to start messing with the 7.4V lipos...

The 6000 is a 1S viewproduct | Turnigy nano-tech A-SPEC 6000mah 1S 65~130C Hardcase Lipo Pack

 

[bapgood]

Haha....I just cracked open the 4200 2S and it's the same height and width, just a little deeper. The Tibs extra large 8400mah

 

[iminuvaping]

just ordered one I went on hobby king as soon as i saw your post.
Was able to find it with copy and past on google but difficult on the actual site unless you specifically search for it.
Thanks again.
Well i think I'm going to need more DNA's cause I've got all kinds of batteries, fuses and just got my helping hands and Hakko FX888D + the extra tips on ebay. LOL
My wife is starting to give me that look if you know what i mean.