My afc cyclone came in

Discussion in 'Reos Mods' started by m3nace, Jan 7, 2014.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    First coil
    30 Guage 10 wrap .94 ohms

    Not the prettiest lol
    [​IMG][​IMG]

    Sent from my SM-N900T using Tapatalk
     
  2. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    Any tips on how it should be done

    Sent from my SM-N900T using Tapatalk
     
  3. Raynman

    Raynman Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Apr 5, 2013
    Location:
    Marion In USA
  4. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    that looks pretty good, just line them up with the air holes. How you like it so far?
     
  5. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    It's pretty awesome I like it a lot ray man it'll have more use when the subohm kits come out gotta play with it a little more the Allen wrench nuts are annoying though will Igo w nuts work

    Sent from my SM-N900T using Tapatalk
     
  6. Big Hitter

    Big Hitter Vaping Master Verified Member ECF Veteran

    Joined:
    Sep 21, 2010
    Location:
    Binghamton, NY
    Nice, not sure ..... but they are screws not nuts :D

    Easy way to remember Male (Guys) are screwers ............. Female (Gals) are nuts :)
     
  7. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    I replaced mine with RM2 spare post screws
     
  8. SLIPPY_EEL

    SLIPPY_EEL Ultra Member ECF Veteran

    Joined:
    Oct 11, 2013
    Location:
    Ω England Ω
    I like the grub screws that come as stnd, I don't know how low your airholes are because you have upgrade version but on the standard setup if you put the top cap up against the side of cyclone you will see that you need to have your coil/s really low to sit in the face of the airhole, it might just be your camera angle but yours might be a bit high, try lowering them :s I get loads of flavour out of mine, its real good :D
     
  9. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    The AFC air holes are higher than the standard cap
     
  10. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    [​IMG] it's a little off center to the air holes unless I open up the air hole all the way

    Sent from my SM-N900T using Tapatalk
     
  11. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    My air holes are not centered to each other, they are both slight to the same side of center, I build the coils to be centered with the holes.
     
  12. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    Thanks I'll do it tomorrow

    Sent from my SM-N900T using Tapatalk
     
  13. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    Do you run dual coil too?

    Sent from my SM-N900T using Tapatalk
     
  14. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    Yes I do, I'm currently using twisted 30 ga kanthal at about .9 ohms
     
  15. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    I can't get mine to line up how did you do it filthy

    Sent from my SM-N900T using Tapatalk
     
  16. Filthy-Beast

    Filthy-Beast Vaping Master Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 14, 2011
    Location:
    Chicago
    Open the holes all the way, take a credit card and put the side in a hole so it contacts both edges of the hole. Do the same with another card on the other hole. The sides of the two credit cards will meet out in front of the atty forming a V. I make my coils so they align with this V. My coils are on an angle compared to the posts, The legs for the outside post are shorter pulling the coil in by that post and the center post legs are longer pushing that side of the coil out farther. Also they are not centered between the posts but pushed more to side of outside post.

    This is an early attempt so they are not perfectly aligned and symmetrical but gives you an idea of what I mean by the V to one side of the atty.

    [​IMG]
     
  17. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    ok cool i did it somehow and my coils are a little messed up but the flavor and thick vapor is there :O thanks bro:D
     
  18. Un5tab1e

    Un5tab1e Super Member Verified Member ECF Veteran

    Joined:
    Jul 18, 2013
    Location:
    United States
    I got mine today. It's definitely got a learning curve. Got it vaping duals at .6 but I know it can do better.

    Sent from my HTC6500LVW using Tapatalk
     
  19. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    can the reos go that low without melting the button? =O
     
  20. m3nace

    m3nace Super Member ECF Veteran

    Joined:
    Oct 18, 2013
    can the reos go that low without melting the button? =O
     
Thread Status:
Not open for further replies.

Share This Page