Parts for original GG telescopic /stormy Early serial under #100

[mudmanc4]

It's been a long time , the GG has served me well. However nothing can last forever.
Looking for the multi threaded end for atty / carty

In the US so any links to these older parts would be appreciated.

Thanks

 

[oplholik]

Might contact Fluid Vapor and see if you can get any info there.

Fluid Vapor - Electronic Cigarettes, Premium US Eliquid, and Accessories.

 

[imeothanasis]

mud, can you please describe again the part you need? Is it the GGTS connector that can accept 801-901-510 and cartos?

 

[AdamAnd]

Post a pic I have two old ggs i might have what you need.

 

[mudmanc4]

That's the one Imeo, any idea where to get it?
I also am in need of the double threaded brass center.

 

[mudmanc4]

 

[imeothanasis]

so you need the double threated SS connector and the center pin mud?

 

[mudmanc4]

The entire connector is torched, 510 thread section is stripped, and the pin / O-ring gone + plastic insulator is very bad.
Also the center brass section which thread onto top & bottom was destroyed (cannot see very well in the images = the telescoping part)

It has served me very well for many years.
Using this one from you at the moment

 

[imeothanasis]

I see mud. So you need the whole atomizer cap (cap - connector - center pin - plastic - o-rings)?

But is this the 4 in 1 connector or the 510 connector?

 

[mudmanc4]

I will take a pic and point specifically, please give me some time, I have to run out for a bit. And thank you for being so quick to reply, both times haha

 

[mudmanc4]

The image should explain what the unit could use to get back up and running.
That and the battery gave up the ghost, Regular 18650 will not squeeze into it, suggestions?
2X17335's?

These are alumininum/brass by the way

 

[imeothanasis]

so you need a brass telescope, a 4 in 1 connector and 2 o-rings mud. Am I right?

 

[mudmanc4]

I could actually do without replacing the brass telescope, however the 4/1 connector really is useless at this pont for more than an 801.

Though, I have started looking around for a tank to use instead of an atty, therefore if there is a cap that might fit this, that will recieve a tank, I might be game. idea's?

 

[Big Ev]

A stealth cap would probably be suitable for a tank.

 

[mudmanc4]

See, I'm so old school I have literally no idea what a stealth cap is without looking.
Tired of dripping 510 attys, went to a local shop today and the tanks stems were all too short to complete enough threads to properly secure the thing.

Link me?

 

[imeothanasis]

Stealth cap mud

THE GOLDEN GREEK MODS :: Stealth Parts :: GG Stealth Atomizer Cap Brass NEW (Old Alloy) with 510 connector inside (no inside pieces included) - Esmokeguru

But be CAREFUL! This cap is in brass as yours but doesnt include the inside pieces. So please send an e-mail to esmokeguru and ask him to put the inside pieces on this cap so you will receive a full working cap.

 

[bones3]

I have been after the inside pieces for the old stealth cap for ages Imeo does ESG have them??

 

[imeothanasis]

he has the plastic only bones, not the pin

 

[mudmanc4]

The issue with these aftermarket tanks, concerning the 4/1, is the threads start after the air cuts in the top, hence they don't catch due to the depth of the cap over the connector.

Is there a GG tank that might work, which I would much rather fit than something or anything else.

The steath cap connector appears roughly the same as the first run connector, which would be the same end result, if i am looking at this correctly. No?

 

[bacc.vap]

Yes mud, it's much the same, just that it's a 510 connection only.