Picture of Your Setup Part 2!

[Mrrickyyap]

kayfun mini sticker setup with super t 14500


Sent from my iPhone using Tapatalk

 

[Beyored]

New brushed aluminium vinyl on front and back panels looks pretty sweet and above all..... No more fingerprints [emoji108]

 

[The.Drifter]

ipv D2 with Black Goblin Mini

 

[G_46]

Ipv d2 with uwell crown

Sent from my D5503 using Tapatalk

 

[Frederick Hew]

After a fresh Polish

Nice phone

 

[BrianG]

IPV D2 with Black Goblin Mini

what battery do you have in that?

 

[The.Drifter]

what battery do you have in that?

In that mod I'm running a LG HG2 3000mah 18650 battery.

LG HG2 3000mah 18650 20A - Sony, Samsung, LG - Mod Batts Chargers

 

[BrianG]

In that mod I'm running a LG HG2 3000mah 18650 battery.

LG HG2 3000mah 18650 20A - Sony, Samsung, LG - Mod Batts Chargers

Thanks. I am getting the CHECK BAT message on mine because of my battery. Problem solved^

 

[cindycated]

Thanks. I am getting the CHECK BAT message on mine because of my battery. Problem solved^

ICR batts are probably not the best to use in mods - that could be why you're getting that message. You want it to say "High Discharge," Like IMR batts, INR for Sammies, VTC for Sonys, or the non-ICR LGs. Also, look at the "continuous discharge rate:" try to find ones that are at least 20A.
My #1 pick is the LG HG2 (3000mAh means longer vape time), #2 is Samsung INR-25R.

 

[TrollDragon]

That battery looks like it had a solder tab removed from the bottom. Did it come from a laptop battery pack? Don't use those at all.

 

[Tonkpils]

ICR batts are probably not the best to use in mods - that could be why you're getting that message. You want it to say "High Discharge," Like IMR batts, INR for Sammies, VTC for Sonys, or the non-ICR LGs. Also, look at the "continuous discharge rate:" try to find ones that are at least 20A.
My #1 pick is the LG HG2 (3000mAh means longer vape time), #2 is Samsung INR-25R.

Sammies are like 6$ no excuse to cheap out on batteries.

 

[mountainbikermark]

Velocity clone on the iStick 100w.

This is why I don't use it while driving

This is ~10 seconds after a sub 3 second inhale with both windows down

1.4 ohm single vertical coil, 10 wrap, 26awg Kanthol, don't remember if it's 3 or 3.5 id, cotton ball wick just touching the bottom of the juice well and I just use the eye dropper to drop juice in it. 80vg/20 pg stuff called Moxxy, all vents wide open, 50 watts.

Support Our Troops!!!
Beast Mode 4
<><

 

[BrianG]

That battery looks like it had a solder tab removed from the bottom. Did it come from a laptop battery pack? Don't use those at all.

I'm grateful nothing bad happened. Just got a Sony battery for this D2. I was using that laptop battery in TC mode with my subtank mini.

 

[rhelton]

ICR batts are probably not the best to use in mods - that could be why you're getting that message. You want it to say "High Discharge," Like IMR batts, INR for Sammies, VTC for Sonys, or the non-ICR LGs. Also, look at the "continuous discharge rate:" try to find ones that are at least 20A.
My #1 pick is the LG HG2 (3000mAh means longer vape time), #2 is Samsung INR-25R.

Maximum discharge capacity of that cell is 4.4amps, the one that OP is using in the D2.

 

[rhelton]

I'm grateful nothing bad happened. Just got a Sony battery for this D2. I was using that laptop battery in TC mode with my subtank mini.

Yah that green samsung you were using is only a 4.4amp max discharge and its a ICR so they go pop when they get hot

 

[rhelton]

Velocity clone on the iStick 100w.

This is why I don't use it while driving

This is ~10 seconds after a sub 3 second inhale with both windows down

1.4 ohm single vertical coil, 10 wrap, 26awg Kanthol, don't remember if it's 3 or 3.5 id, cotton ball wick just touching the bottom of the juice well and I just use the eye dropper to drop juice in it. 80vg/20 pg stuff called Moxxy, all vents wide open, 50 watts.

Support Our Troops!!!
Beast Mode 4
<><

I like using coils around 1.0 ohm on my regulated mods.

 

[rhelton]

Here is my newest mod. Hana Modz One mod DNA40 with my Hurricane

 

[BrianG]

I did the same with my subtank it's alot of work but worth it in the end....
Be nice to see how it turns out.... [emoji106]
Good luck.....

After removing paint with 100grit. Raw Evic VT. The top piece is actually chrome plated copper. Give me another week and I'll have this thing blinging

 

[mountainbikermark]

I like using coils around 1.0 ohm on my regulated mods.

My brain is still stuck on the old days when I used to get insane results from my T2 tanks by using cotton yarn and making it a little longer than just touching the bottom of the well so my thinking is juice flow is as important as current flow, why I like the bigger id wraps.

Support Our Troops!!!
Beast Mode 4
<><

 

[Beyored]

After removing paint with 100grit. Raw Evic VT. The top piece is actually chrome plated copper. Give me another week and I'll have this thing blinging

Can that be easily taken apart.... Its so much easier working with just the shell.....