protank 2 question

Discussion in 'New Members Forum' started by saintsfan, Dec 3, 2013.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. saintsfan

    saintsfan Full Member

    Joined:
    Oct 5, 2013
    Location:
    Sunset, Utah, United States
    my wife and i both have a pt2, she is using hers on a ego winder and i am using an mvp v2, my question is what is a good resistance for replacement heads that will work for both. i have my MVP down to 3.7v or 6w, anything over that i get a burnt taste, but on the ego 4v is good, any ideas or advice to eliminate the burnt taste?
     
  2. Wingsfan0310

    Wingsfan0310 Ultra Member ECF Veteran

    Joined:
    Oct 2, 2013
    Location:
    Flat Rock, MI, USA
    I'd get the 2.5 ohm heads. The higher the resistance, the less power the heads will see at a set voltage. Too much power = burnt juice
     
  3. saintsfan

    saintsfan Full Member

    Joined:
    Oct 5, 2013
    Location:
    Sunset, Utah, United States
    that's what i was thinking, wanted to get some advice first. also what about removing one of the flavor wicks, what is the advantage,more flavor?
     
  4. Wingsfan0310

    Wingsfan0310 Ultra Member ECF Veteran

    Joined:
    Oct 2, 2013
    Location:
    Flat Rock, MI, USA
    Well if your getting dry hits, removing a flavor wick will allow more juice into the head, getting rid of the dry hits. But it can also lead to too much juice into the head leading to flooding/gurgling
     
  5. saintsfan

    saintsfan Full Member

    Joined:
    Oct 5, 2013
    Location:
    Sunset, Utah, United States
    i will try the 2.5 without removing flavor wicks first, thanks for your info wings.
     
  6. Wingsfan0310

    Wingsfan0310 Ultra Member ECF Veteran

    Joined:
    Oct 2, 2013
    Location:
    Flat Rock, MI, USA
    Your welcome. You can always try removing a flavor wick from your current heads to see if it was dry hits causing the burnt flavor, just don't throw it away. If it starts flooding, just reinstall it. Always glad to help a fellow vaper!
     
  7. desmondsg

    desmondsg Senior Member Verified Member ECF Veteran

    Joined:
    Sep 5, 2013
    Location:
    Singapore
    Try rebuilding with cotton wicks. Cotton are cheap and easily available. Wicks very well so it prevents dry hits.
     
  8. pinballtommy

    pinballtommy Full Member

    Joined:
    Aug 29, 2013
    Location:
    New York
    I find protank 2 works best on 2.2 coil heads for vaper, TH & flavor. Also keep in mind the flavor wick might
    help to prevent juice from spitting into your mouth!
     
  9. Operator1978

    Operator1978 Full Member

    Joined:
    Nov 21, 2013
    Location:
    Ohio
    I would go with 2.2 or 2.5
    Both work well in my pt2
     
  10. Mark Anthony

    Mark Anthony Vaping Master Verified Member ECF Veteran

    Joined:
    Oct 4, 2013
    Location:
    Scranton, Pa USA
    This is great advice. I use organic cotton from CVS and it's only about $4 for a large bag.
     
  11. mightymen

    mightymen La RĂ©sistance ECF Veteran

    Supporting member
    Joined:
    Nov 22, 2012
    Location:
    USA
    KangerTech Chart came with all my Protanks 2's.

    Suitable Voltage to different Resistance

    1.7 - 1.9 ohms / 3.1 - 3.3 volts
    2.1 - 2.3 ohms/ 3.4 - 3.7 volts
    2.4 - 2.6 ohms/ 3.8 - 4.1 volts
    2.6 - 3.0 ohms/ 4.2 - 4.5 volts
     
  12. WindyCityJoe

    WindyCityJoe Super Member Verified Member ECF Veteran

    Joined:
    Oct 6, 2013
    Location:
    Phoenix, AZ
    Looks like its all right there in a nutshell, good luck
     
  13. saintsfan

    saintsfan Full Member

    Joined:
    Oct 5, 2013
    Location:
    Sunset, Utah, United States
    guess i should open the little booklet that comes with the tank huh lol
     
Thread Status:
Not open for further replies.

Share This Page