Reo at 5v?

Discussion in 'Reos Mods' started by want to quit, Jun 21, 2011.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. want to quit

    want to quit Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 26, 2011
    Location:
    Germany/ Atlanta, GA
    Hi guys,

    now my first reo was a grand love it now I got the mini love it even more and now I am of course considering a woody but still trying to figure out which one te mini wood or grand wood.

    Now I found a question that will decide on my decision and would like to know can you vape at 5v with the reo woodville? Or is it 3.7v and 6v but 5v is not possible?

    Hope my reo family jumps in and finds an answer for me.

    Thanks everyone
     
  2. Mudflap

    Mudflap Vaping Master Verified Member ECF Veteran

    Joined:
    Dec 19, 2010
    Location:
    Tyler, Texas
  3. want to quit

    want to quit Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 26, 2011
    Location:
    Germany/ Atlanta, GA
    Haha a whole 6 mins to get the answer gotta love the reo family. Thanks buddy
     
  4. want to quit

    want to quit Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 26, 2011
    Location:
    Germany/ Atlanta, GA
    One more question I know a LR 306 will die at 6v but what to use at 5v? Would I be better
    off with a hv 306 or can I use a LR at 5v?
     
  5. Mudflap

    Mudflap Vaping Master Verified Member ECF Veteran

    Joined:
    Dec 19, 2010
    Location:
    Tyler, Texas
    Personally, I think 5 volts is best matched up with 2.5 to 3.5 Ω atties/cartos. It might actually pop your LR atties.
     
  6. bjannr

    bjannr Ultra Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Aug 23, 2010
    Location:
    NE Pennsylvania
    Haven't tried a 306, but I have used LR cartomizers on my Grand at 5V.
     
  7. want to quit

    want to quit Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 26, 2011
    Location:
    Germany/ Atlanta, GA
    Thanks a bunch Mud great info much appreciated
     
  8. want to quit

    want to quit Ultra Member Verified Member ECF Veteran

    Joined:
    Mar 26, 2011
    Location:
    Germany/ Atlanta, GA
    Thanks bjannr you should give the 306 a go I really enjoy them. Sadly I cannot do cartos I don't know why but I cannot do it on the reo. I use them on my other Pv's from time to time but to me the Reo=Atty but that may just be my opinion. Thanks for the help though bjannr.
     
  9. Landlord

    Landlord Vaping Master Verified Member ECF Veteran

    Joined:
    Jan 30, 2011
    Location:
    Cleveland Ohio
    I use the 5 volts all the time. Here is a couple pics. One is no load and one is under load of a standard Joye atty..
    [​IMG]
    [​IMG]
     
  10. wigglr

    wigglr Ultra Member Verified Member ECF Veteran

    Joined:
    Feb 23, 2011
    Location:
    Massachusetts
    so Landlord (I'm pretty ignorant/dumb when it comes to electrics/wiring/V/W....) the bottom picture shows a 4.6 -- does that mean when you are hitting it you are only getting 4.6V out of the battery, not 5?

    So when calculating watts, I should plug in 4.6 - 4.8 instead of 5 in order to decide what resistance atomizer I want to achieve those watts? I like a hotter hit -- so if I am using that battery it looks like I should go lower in ohms than I thought (I put 5 into the watts calculator)
     
  11. marcalbar

    marcalbar Super Member Verified Member ECF Veteran

    Joined:
    Dec 30, 2009
    Location:
    Philippines
    I'm eager to try the 5v setup on my Grand as well. Just ordered a couple of them from Randy @rtdvapor! :D
    I've tried the dual coils on another 5v pv and I loved it so I hope it does the same for my Grands.

    Right now, I'm loving Boge 2ohm cartos and dual coil cartos on my Grands. Can't seem to get the hand of atties.
     
  12. mwa102464

    mwa102464 ECF Guru ECF Veteran

    Joined:
    Oct 14, 2009
    Location:
    Outside of the Philadelphia Burbs, NJ & Fla
    I run the 5v all the time as well, try it with a good 2ohm Atty its a super vape !
     
  13. keyzygirl

    keyzygirl ECF Guru ECF Veteran

    Joined:
    Aug 10, 2009
    Location:
    Key West,Fl.
    This is very interesting.Im looking at a purple Grand.I need 5v and this will work.
     
  14. Mvgratz

    Mvgratz Vaping Master Verified Member ECF Veteran

    Joined:
    Jan 29, 2011
    Location:
    Alabama
    The wattage produced is more or less a measurement of power or heat. The resistance to the applied voltage creates the wattage.
    So, the more voltage applied, OR the lower the resistance to the voltage the more wattage produced, thus more heat...:evil:
     
  15. wigglr

    wigglr Ultra Member Verified Member ECF Veteran

    Joined:
    Feb 23, 2011
    Location:
    Massachusetts
    Thanks, Mike but I think I have that part down (FINALLY!)
    My real question (I am terrible at getting those across) was:
    is the output of the battery actuallllly ~4.6(at least for the battery in the picture) and NOT 5V. Because I am looking at that battery and trying to decide what atomizer to use. When using the ohms law calculator, I keep putting in 5(V) into the calculator and my desired wattage in order to know what resistance atomizer I should buy. However, would I be "misled" by presuming that the total watts would be a product of 5(V)? as it seems the V I should input into the calculator is actually something like 4.6-4.8 and then decide what atomizer I should get using my desired wattage and 4.6-4.8 insteaad of 5


    AND BREATHE
     
  16. Mvgratz

    Mvgratz Vaping Master Verified Member ECF Veteran

    Joined:
    Jan 29, 2011
    Location:
    Alabama
    What your seeing is known as the voltage drop caused by the resistance of the atty. The wattage produced is a direct result of the applied voltage, not the under load reading that shows the voltage drop. In order to get a specific wattage out, you must use the correct applied voltage in the ohms law calculator. Not what it is after the resistance of the atomiser reduces it. Understand?
     
  17. wigglr

    wigglr Ultra Member Verified Member ECF Veteran

    Joined:
    Feb 23, 2011
    Location:
    Massachusetts
    Mike. Thanks for sticking this one out with me HAHA :)

    Now I believe I understand... I should NOT use the V depicted in the bottom picture of his that shows the 4.6 (the voltage drop picture) in the ohms calculator
    However, the batteries themselves say 4.8 - so should I use 4.8 or 5? (Not really sure how big of a difference that makes, though)

    Once again, Mike you're awesome
     
  18. Mvgratz

    Mvgratz Vaping Master Verified Member ECF Veteran

    Joined:
    Jan 29, 2011
    Location:
    Alabama
    Many Many years of electronics school and hands on Electronics Technician at a couple of companies..anyhow. Here's the info you need to use. The REAL accurate, actual voltage of your batts fresh off the charger, and the real measurement of the attys your using. Do you have a digital multimeter?
     
  19. wigglr

    wigglr Ultra Member Verified Member ECF Veteran

    Joined:
    Feb 23, 2011
    Location:
    Massachusetts
    As of right now, I don't -- but I am researching prices so I can buy one with my paycheck on Friday. I went to buy one this weekend at Home Depot and Lowes -- cheapest I saw was $20 .... RTD had one for 9
    Any suggestions?
     
  20. wigglr

    wigglr Ultra Member Verified Member ECF Veteran

    Joined:
    Feb 23, 2011
    Location:
    Massachusetts
    Wait so if I am using 18650s... I should use that number that can be like 4.xx (ex: 4.19) and NOT 3.7 like I have been doing?
     
Thread Status:
Not open for further replies.

Share This Page