Heres a review of the Furytank by Anyvape sent from GearBest for purposes of review.
The anyvape furytank is a subohm tank that has an interesting feature when top filling that allows you to fill from the top without the need to close off any air hole or tilt the tank at all or even use any tools or plugs. This is done by a unique system that uses a spring to push down the chimney section down the tank covering the whole coil head including the juice channels when the top part of the tank is unscrewed. The sega tank by anyvape was Anyvape's previous subtank with apparently a similar mechanism to stop leaks during top filling but the view of your eliquid level was quite restricted compared to the furytank. Before the segatank, they had a tank called the davide tank that was similar to the protank by kanger and nautilus by aspire.
The tank achieves this lack of flooding when top filling by having the chimney section in 2 parts, one is the chimney tubing and the other is the top of the tank both connected together with a strong spring system creating 1 unit. When the unit is disassembled from the top screw on section as well as the base of the tank, the chimney section including the top are extended due to the spring. This section is possibly press fit some how and does not come apart. The tank came clean enough but I washed it with soap anyway and no soap was left behind as far as could be noticed in the spring section. There is however some water surrounding the spring that may take a few compressions of the chimney section to dry out. I switched juices a few times too and didn't notice too much juice staying in the tank compared to other ones, so the spring area does not seem to retain much liquid.
When the tank is put together with either the pre made coil or the rba section included, the spring is compressed slightly but still hides the juice channels and coil head. When you start to screw on the top section you can see some threading at the top of the chimney that corresponds to the threading in the top cap that it catches and whilst you screw down the cap will thread along the threading of the chimney revealing the coil head and juice channels. It takes a bit more force to thread down to the top cap and possibly a few more turns too but its quite an easy process and easy to catch the threads.
At the top cap area theres also a small air flow control ring to let in air along with the vapor that makes it an airier draw as well as a cooler draw. I found it to be of use mainly with higher watts above 30w.
The pre made coil seemed to keep up with wicking decent at 30 ish watts but at around 40+ it was not possible to take as long a draw as it would produce a dry hit towards the end of the vape. The vape at 30-35w was good though, no noticeable spitting of juice, not too hot and the flavor was good with no noticeable muting or cotton taste even in the first tank of liquid.
The stock coil head has a "scissor" setup when theres 2 layers of horizontal coils with both coils at 90 degrees from the other one forming an "x" or scissor bottom dual coil as its labelled. This could be to help with wicking as all 4 coil end are then at 90 degrees from eachother covering the whole coil head.
The RBA section is included as well with a coil and cotton already installed. It came with a fair bit of cotton though which could possibly strain the liquid flow so I removed it to test out builds and found that a 2mm coil was best suited due to the position of the 2 posts being quite close. Also as you attach the wire around the screw it was tricky to fix any very thick wires or clapton coils. The rba apparently also fits any aspire atlantis tanks or tanks accepting those heads. The furytank then also accepts the aspire atlantis coils. It seems at the moment the pre made coils specifically for the furytank are not available but the atlantis ones apparently work fine instead.
Included in the package is the tank with 1x 0.3ohm pre made coil, 1x rba head, 1x spare glass and other accessories including cotton, coils for the rba, screw driver and spare o-rings. My pack was a sample and didn't come with spare cotton, o-rings, rba coils or a screw driver! However I did notice these on other peoples packs.
Theres 4 airholes in total which produce a good amount of airflow in combination with the air holes at the bottom of the coil as well as the chimney width and wide bore drip tip. It may be possible to create an mtl head with thin wire and higher ohms as well as closing off the airflow, but have not tried that yet. I tried some cinnamon flavor in the tank however and didnt notice any problems with the glass or o-rings even after many days use.
Overall its an interesting tank with the top fill system being unique and the fact that it comes with an rba head is good. The rba is quite small though so might not be easy with thicker wires and it needs to be around 2mm diameter to fit. The pre made coil seems to last a while too and wick decent, maybe theyll be releasing packs of them soon. Also quite reasonably priced compared to other similar tanks. The vape was consistent and good and was easy to fill each time with no mess
Some specs:
Type: Clearomizer
Brand: Anyvape
Model: Fury Tank
Available Color : Silver
Feature: Rebuildable, Detachable, Cleanable
Material : Stainless steel, Pyrex Glass
Thread Type: 510
Tank Capacity : 5.0ml
The Anyvape furytank can be purchased from GearBest at Original Anyvape Fury Tank Clearomizer ( Updated New Version 100 percent Leak Free )-19.99 and Free Shipping| GearBest.com
currrently priced at $19.99
The anyvape furytank is a subohm tank that has an interesting feature when top filling that allows you to fill from the top without the need to close off any air hole or tilt the tank at all or even use any tools or plugs. This is done by a unique system that uses a spring to push down the chimney section down the tank covering the whole coil head including the juice channels when the top part of the tank is unscrewed. The sega tank by anyvape was Anyvape's previous subtank with apparently a similar mechanism to stop leaks during top filling but the view of your eliquid level was quite restricted compared to the furytank. Before the segatank, they had a tank called the davide tank that was similar to the protank by kanger and nautilus by aspire.
The tank achieves this lack of flooding when top filling by having the chimney section in 2 parts, one is the chimney tubing and the other is the top of the tank both connected together with a strong spring system creating 1 unit. When the unit is disassembled from the top screw on section as well as the base of the tank, the chimney section including the top are extended due to the spring. This section is possibly press fit some how and does not come apart. The tank came clean enough but I washed it with soap anyway and no soap was left behind as far as could be noticed in the spring section. There is however some water surrounding the spring that may take a few compressions of the chimney section to dry out. I switched juices a few times too and didn't notice too much juice staying in the tank compared to other ones, so the spring area does not seem to retain much liquid.
When the tank is put together with either the pre made coil or the rba section included, the spring is compressed slightly but still hides the juice channels and coil head. When you start to screw on the top section you can see some threading at the top of the chimney that corresponds to the threading in the top cap that it catches and whilst you screw down the cap will thread along the threading of the chimney revealing the coil head and juice channels. It takes a bit more force to thread down to the top cap and possibly a few more turns too but its quite an easy process and easy to catch the threads.
At the top cap area theres also a small air flow control ring to let in air along with the vapor that makes it an airier draw as well as a cooler draw. I found it to be of use mainly with higher watts above 30w.
The pre made coil seemed to keep up with wicking decent at 30 ish watts but at around 40+ it was not possible to take as long a draw as it would produce a dry hit towards the end of the vape. The vape at 30-35w was good though, no noticeable spitting of juice, not too hot and the flavor was good with no noticeable muting or cotton taste even in the first tank of liquid.
The stock coil head has a "scissor" setup when theres 2 layers of horizontal coils with both coils at 90 degrees from the other one forming an "x" or scissor bottom dual coil as its labelled. This could be to help with wicking as all 4 coil end are then at 90 degrees from eachother covering the whole coil head.
The RBA section is included as well with a coil and cotton already installed. It came with a fair bit of cotton though which could possibly strain the liquid flow so I removed it to test out builds and found that a 2mm coil was best suited due to the position of the 2 posts being quite close. Also as you attach the wire around the screw it was tricky to fix any very thick wires or clapton coils. The rba apparently also fits any aspire atlantis tanks or tanks accepting those heads. The furytank then also accepts the aspire atlantis coils. It seems at the moment the pre made coils specifically for the furytank are not available but the atlantis ones apparently work fine instead.
Included in the package is the tank with 1x 0.3ohm pre made coil, 1x rba head, 1x spare glass and other accessories including cotton, coils for the rba, screw driver and spare o-rings. My pack was a sample and didn't come with spare cotton, o-rings, rba coils or a screw driver! However I did notice these on other peoples packs.
Theres 4 airholes in total which produce a good amount of airflow in combination with the air holes at the bottom of the coil as well as the chimney width and wide bore drip tip. It may be possible to create an mtl head with thin wire and higher ohms as well as closing off the airflow, but have not tried that yet. I tried some cinnamon flavor in the tank however and didnt notice any problems with the glass or o-rings even after many days use.
Overall its an interesting tank with the top fill system being unique and the fact that it comes with an rba head is good. The rba is quite small though so might not be easy with thicker wires and it needs to be around 2mm diameter to fit. The pre made coil seems to last a while too and wick decent, maybe theyll be releasing packs of them soon. Also quite reasonably priced compared to other similar tanks. The vape was consistent and good and was easy to fill each time with no mess
Some specs:
Type: Clearomizer
Brand: Anyvape
Model: Fury Tank
Available Color : Silver
Feature: Rebuildable, Detachable, Cleanable
Material : Stainless steel, Pyrex Glass
Thread Type: 510
Tank Capacity : 5.0ml
The Anyvape furytank can be purchased from GearBest at Original Anyvape Fury Tank Clearomizer ( Updated New Version 100 percent Leak Free )-19.99 and Free Shipping| GearBest.com
currrently priced at $19.99
