review: The Poldiac mechanical mod by mmvapors.com

Discussion in 'E-Cigarette Video Reviews' started by manimal, Mar 5, 2013.

Thread Status:
Not open for further replies.
  1. manimal

    manimal Senior Member Verified Member ECF Veteran

  2. pounder

    pounder Super Member Verified Member ECF Veteran

    Nice review. I like the looks and quality of the build on the Poldiac more than the never available GG. Will order this one asap.
     
  3. ukeman

    ukeman PV Masher Verified Member ECF Veteran

    Supporting member
    3.96 UNDER LOAD!!! yow... who'd a thunk... whoa the price is high.. .heheh I have one and LOVE IT with my Cobra 3mil; .9 Ohm 28g 4/3 wrap.
    IMG_0054.jpg I use 18650 AW IMR or MNKE IMR 18650, and it lasts a hell of a long time
     
  4. manimal

    manimal Senior Member Verified Member ECF Veteran

    yeah, this is definitely the best mechanical mod that I've tried.
     
  5. manimal

    manimal Senior Member Verified Member ECF Veteran

    yeah, it definitely pumps out the power.
     
  6. manimal

    manimal Senior Member Verified Member ECF Veteran

    Thanks, if you get ahold of one of these, The gg will seem kind of weak. still love my stealth though.
     
  7. ukeman

    ukeman PV Masher Verified Member ECF Veteran

    Supporting member
    Yeah I hope this one stays in production a long time ...MMVapors has a good rep, and rnm reviews on youtube does a full breakdown and setup on its features...
    I was lucky to get mine like new on classies... before anyone else saw it heheh; at near to retail... I haven't even tried the smaller legs yet and will probably look for some good 18500 IMRs..
    Using AW IMR 18650's and I also have a couple MNKE's which cost more ... for the price (15 at avidvaper) I don't know if the difference is worth it... supposed to hold its high output longer... but when i have almost a doz 18650's in rotation it doesnt really matter.

    gotta say the Cobra, with its 1mm airhole "tight" draw is perfect for a hard hitting device.
     
  8. Blix

    Blix Ultra Member Verified Member ECF Veteran

    Crazy good under load!
     
  9. TheSneakerHoarder

    TheSneakerHoarder Ultra Member Verified Member ECF Veteran

    Nice. My UMA 18350 will be here tomorrow.

    As much as I love my GGTS, I cannot fall in love with the button--I'm hoping the Poldiac is exactly what I've been wishing my GGTS was.
     
  10. ukeman

    ukeman PV Masher Verified Member ECF Veteran

    Supporting member
    One issue i have so far; haven't thought about a fix... my Cobra air hole/wick alignment is off with the Poldiac top button.
    I don't like fiddling so I just contort my hand a bit to keep it tilted right and fire/vape.

    ? Does the Poldiac or mechanicals in general have no cut off for firing? I mean can I keep holding the fire button for any length? so used to my regulated VV's (most sold off now).

    actually i suppose i could try another hole for the wick in the Cobra
     
  11. Blix

    Blix Ultra Member Verified Member ECF Veteran

    It's mechanical , there is no cut-off or auto anything, it cuts off when you release the fire button... :)
     
  12. manimal

    manimal Senior Member Verified Member ECF Veteran

    there is no cut off on any mechanical mods. the only way to line up the airhole with the button on the poldiac, is to create a slight gap by raising the center post.
     
  13. manimal

    manimal Senior Member Verified Member ECF Veteran

    indeed, my friend.
     
  14. manimal

    manimal Senior Member Verified Member ECF Veteran

    i think that your poor gg will get neglected, sneakerhoarder. haha.
     
  15. tenshi

    tenshi Super Member Verified Member ECF Veteran

    Love it too :D. Hits like a champ. Gotta go buy the some fancy shirts and pants for it next lol ac9 on my poldiac.jpg
     
  16. manimal

    manimal Senior Member Verified Member ECF Veteran

    This thing probably has more outfits than I do, haha.
     
Thread Status:
Not open for further replies.

Share This Page