Smoant battlestar "No Atomizer Found"

[z0n3x]

hey guys i have problem with my smoant battlestar 200w it says "No Atomizer Found"
so i have tryed 3 atomizer's: 1. smoke beast 2. melo 3 3. tsunami rda
and all of them have same problem
when i desconnect atomizer... mod ask me new coil or same coil and when i connect atomizer back to mod and select new coil i can vape like 1 to 2 times and it say "No Atomizer Found" agane...
how can i solve this problem... it started 5 days ago and i tryed evrything...

 

[Thompsonhunt]

Well sounds like it's not making a connection. So it could be that you're tightening the tanks too much or it could be an issue with the device itself

Sent from my SM-G920T using Tapatalk

 

[madstabber]

Sounds like a connection problem. Maybe you got some sticky juice on the 510 and it's stuck down. Get a toothpick and pry on it a little bit.

 

[djsvapour]

The Battlestar has a very high 510 pin in the mod and shallow threads. You have probably inadvertently over-tightened your tanks and pressed it down too far.
Probably fixable.

 

[stols001]

Yes, since you're able to get a connection a couple times, the mod is probably salvageable. If you bought it from a brick and mortar store, I would take it in, unless you are highly mechanically minded (I am most certainly not) I have found vape shops here to be friendly and helpful, even if you haven't purchased it from them, I was able to get several things repaired, early on, when I dropped them.... The shop I go to has an electronics specialist, and he seems to have fun bringing really MESSED up items to life.... I had a rechargable only fixed battery setup that looked like the leaning tower of Pisa, but he fixed it! I usually would by a bottle of juice as a "thank you" even if I didn't need one.

If you can't do that, you can probably send it to the manufacturer, especially if under warranty.

(Through this site) I have learned that I can usually find a youtube video that's a review/demonstration, that will help me figure out all the functions in my mod and how to use it--- I do read the instructional information, but that doesn't always help me *as much* as watching someone demonstrate use and point out any issues or problems (they all have them, watching a review of my IPV-5 helped me realize my door was coming off because one of the magnets was in the wrong place, which seems to be a fairly common design flaw... It's been great since I fixed it, even dropping it

Good luck! If you have to wait awhile for a fix, find something cheap and easily available that you can use now, then as a backup if ever needed.

Anna

 

[z0n3x]

so now its "work" and its read that my coil have 4.46 ohm like wtf? on all 3 atomizers and after few times i vape it say its too hot... idk what the heck is with this mod...

 

[listopencil]

so now its "work" and its read that my coil have 4.46 ohm like ...? on all 3 atomizers and after few times i vape it say its too hot... idk what the heck is with this mod...

I would suggest that you do not use that mod again until you can get it fixed or replaced. If this happened to me, I would put it down and walk away until I was sure that it was completely cooled off. Then remove the batteries. Then contact whoever sold it to you and explain the problem. You really don't want to be messing with a malfunctioning 200 Watt mod if you don't know what you are doing.

 

[Smoke_too_much]

Those ohm readings could be coming because of a problem with the connection or just as likely the mod is not working correctly. Make sure your 510 connection is clean and not pressed down & stuck there like djsvapour has said. If that isn't it then take/send it back for a replacement.

 

[z0n3x]

its not hot... u can rip it just one time on 50w and it will say too hot... i send meil to smoant so i will see what they will answer to me... i dont have founds to get another mod for now and i need to fix this one asap