Temreture Control issue

[Ali Abbas]

This is my first post and all your help is appreciated.

I have an issue that I can’t fix since buying my DNA200 Boxer 133 mod.

Temp Control hits quickly and the vape is cold.

My setup is:

Boxer DNA200 133
SS316l CSV from steam engine
tank: Serpent mini 25
SS316l AWG 26 6 wraps spaced 0.42ohm

I vape at 410F 25W



I have tried several csv files with no luck, however the same setup is working fine on Yihi.

What do your think is a setting problem or a build issue?

 

[jseah]

This is my first post and all your help is appreciated.

I have an issue that I can’t fix since buying my DNA200 Boxer 133 mod.

Temp Control hits quickly and the vape is cold.

My setup is:

Boxer DNA200 133
SS316l CSV from steam engine
Tank: Serpent mini 25
SS316l AWG 26 6 wraps spaced 0.42ohm

I vape at 410F 25W



I have tried several csv files with no luck, however the same setup is working fine on Yihi.

What do your think is a setting problem or a build issue?

I have never had any luck using TC with SS316 wire on a DNA 200. It works great with Ni and Ti. With SS, as soon as I hit the fire button TC kicks on and the vape is almost nonexistent.

Sent from my SM-G935V using Tapatalk

 

[Dubminer]

This is my first post and all your help is appreciated.

I have an issue that I can’t fix since buying my DNA200 Boxer 133 mod.

Temp Control hits quickly and the vape is cold.

My setup is:

Boxer DNA200 133
SS316l CSV from steam engine
Tank: Serpent mini 25
SS316l AWG 26 6 wraps spaced 0.42ohm

I vape at 410F 25W



I have tried several csv files with no luck, however the same setup is working fine on Yihi.

What do your think is a setting problem or a build issue?

I would try going up to maybe 450F. I use the same coil but on a DNA 75. I do not like a too warm vape and i switch between 430F and 450F.

 

[Matty316]

Never used a DNA200 chip and can't remember if it has a manual/custom TCR setting but if it does try using it with a TCR set to 0.00092 for ss 316l. It works well on my IPV5.

Take a look at this thread The Ultimate TCR List I found it very useful.

 

[jseah]

Never used a DNA200 chip and can't remember if it has a manual/custom TCR setting but if it does try using it with a TCR set to 0.00092 for ss 316l. It works well on my IPV5.

Take a look at this thread The Ultimate TCR List I found it very useful.

The DNA200 chip doesn't allow you to set a TCR lower than 0.001.

 

[Matty316]

The DNA200 chip doesn't allow you to set a TCR lower than 0.001.

Ah I see. Well that's a shame. Hopefully they will bring out a firmware upgrade with a wider TCR range.

 

[Ed_C]

I think your temp is too low. I just got a Lavabox DNA75 with a Serpent Mini (first DNA and first RTA). I even have the same build as you, but I'm reading 0.46 ohms. I'm also using the Steam Engine SS316L csv file. I'm at 480F and I get a good vape, but even at that temp, it's not really that warm at all. The resistance sounds low on yours. My coil is 3mm, is yours the same?

 

[Ali Abbas]

I think your temp is too low. I just got a Lavabox DNA75 with a Serpent Mini (first DNA and first RTA). I even have the same build as you, but I'm reading 0.46 ohms. I'm also using the Steam Engine SS316L csv file. I'm at 480F and I get a good vape, but even at that temp, it's not really that warm at all. The resistance sounds low on yours. My coil is 3mm, is yours the same?

Yes the same 3mm.




Sent from my iPhone using Tapatalk