The New Official Post Your Coil Porn Thread

[EvlSmrk]

The only question is how to fuse it, 44g? 46g? Alternating 44/46? Microclap? Alternating microclap? Too many options haha

Sent from my XT1585 using Tapatalk

Say what now? Care to run that by me again. Thought I was following you, but then nope.

 

[Tom Forde]

Say what now? Care to run that by me again. Thought I was following you, but then nope.

Options for fusing those two halves together. Don't know what I'm going to do, as in use a 44g fuse, a 46g fuse, 44g & 46g alternating every other stagger, 40g/46g micro-clapton etc. So many choices.

Sent from my XT1585 using Tapatalk

 

[RedheadedBStarD]

4 loop 34g N80 flat vertebraid twisted with 24g ss316l. 4.75mm ID, 0.29 ohms. Big punch you in the tongue flavor!

 

[EvlSmrk]

Options for fusing those two halves together. Don't know what I'm going to do, as in use a 44g fuse, a 46g fuse, 44g & 46g alternating every other stagger, 40g/46g micro-clapton etc. So many choices.

Sent from my XT1585 using Tapatalk

Ahhhh. Thought that is were you were headed. Just to make things awesome looking, I'm going to suggest alternating between 44 and 46. Haven't worked with anything smaller than 36g myself, but your skills are much higher than mine.

 

[Tom Forde]

Ahhhh. Thought that is were you were headed. Just to make things awesome looking, I'm going to suggest alternating between 44 and 46. Haven't worked with anything smaller than 36g myself, but your skills are much higher than mine.

Skills is a relative term. Ill tell you, I've failed way more than I've succeeded in building. Sometimes you get it perfect sometimes things get complicated.

Triple double end result did one with 44g one with 46g

Sent from my XT1585 using Tapatalk

 

[juicynoos]

I'm no big shakes when it comes to fancy coil creation but am in awe of what I see on this thread when I stop by.
Just got a Baal v3 that I need to build a 0.45-0.55 dual Clapton to try in series mod. I'm looking at 11/12 wraps with these wires of 24 core wrapped in 30 awg kanthal. Any tips on putting this build together would be much appreciated.

 

[Tom Forde]

Quick wireporn shot

Haven't coiled that up yet, I don't wanna break the 46g with my clumsy fingers haha

Sent from my XT1585 using Tapatalk

 

[RedheadedBStarD]

I got some close-up filters to fit the lens of my dslr yesterday (cheap way to go macro) and banged this coil out to do some test shots. Some shots focus stacked, others not.

Fused Clapton with different sized cores. 1 - 24g ss316l, 1 - 28g ss316l, wrapped in 32g N80. 0.30 ohms and a 4.75mm ID.

 

[RedheadedBStarD]

26g ss316l wrapped in .4 N80 ribbon, parallel with 26g ss316l wrapped in twisted 32+36g N80. 4.75mm ID and 0.25 ohms.

No editing to photos other than focus stacking.

 

[Kenway]

24gauge parallel 5wraps // I.D 3mm

SMPL mod // KENNEDY DEMON ATTY

0.16ohms
85watts
26amps

 

[Tom Forde]

This thread is not dying on me!

Sent from my XT1585 using Tapatalk

 

[Taowulf]

My poor contribution of a framed staple...yeah, that is 32ga for the wrap, I am out of anything smaller for at least a month.

 

[Tom Forde]

My poor contribution of a framed staple...yeah, that is 32ga for the wrap, I am out of anything smaller for at least a month.

If you have 30 or 32 as your highest gauge, by chance do you have any 18g? Id say make up some arched Claptons. They're "fancy" and vape like a poor man's aliens. In all reality they're a great vape. Ohm out a bit low depending on what your cores are though.

Sent from my XT1585 using Tapatalk

 

[Taowulf]

22ga is the largest I have. I will looked up arched though. I have probably seen them, just can never remember all the names.

 

[RedheadedBStarD]

24g SS316L space claptoned with a 30g KA1 3 loop Celtic braid. 0.30 ohms; 4.76mm ID. Don't know if it was because of the kanthal braid wrap, or what but blew right through most the color range. Tastes good though.

Only editing was focus stacking and adding the watermark.

 

[Tom Forde]

Kind of groove fused things in the 2 post K24. Spacing is super hard to eye out with these things.

Sent from my XT1585 using Tapatalk

 

[SLIPPY_EEL]

Kind of groove fused things in the 2 post K24. Spacing is super hard to eye out with these things.

Sent from my XT1585 using Tapatalk

Nice clouds!

 

[Tom Forde]

Nice clouds!

Thanks slip! Here's more coilporn.
Interlocking 40g over a 10ply .4/28g fraple.

Sent from my XT1585 using Tapatalk

 

[Taowulf]

2500ft of wire will be here next week. Mmmmm, build orgy incoming.

 

[SLIPPY_EEL]

Thanks slip! Here's more coilporn.
Interlocking 40g over a 10ply .4/28g fraple.

Sent from my XT1585 using Tapatalk

Nice build!
I have a similar build going on but without the interlock
Ima post it in the other thread to keep her alive