Do not disturb
Well, I did it... first coil build ever.
About 7 wraps of 28ga Kanthal on a 3mm diameter tool. 1.5 ohms.
This flat top bellcap KFL+ V2 Frankenstein is good... real good. Flavor is right there with my Vika Fantasy, and I haven't found anything that i could say that about.
My only small complaint is the air hole whistle. I ended up taking the airflow screw out of the bottom and covering the side one with my finger. Maybe radiusing the hole with Dremel could fix that.
Happy camper I am. Thanks everyone for the assistance and especially @Two Bears.
Sent from Uranus using Tapatalk
Good for you![emoji106] Doesn't it feel good to enjoy something you made?!
Well, I did it... first coil build ever.
About 7 wraps of 28ga Kanthal on a 3mm diameter tool. 1.5 ohms.
This flat top bellcap KFL+ V2 Frankenstein is good... real good. Flavor is right there with my Vika Fantasy, and I haven't found anything that i could say that about.
My only small complaint is the air hole whistle. I ended up taking the airflow screw out of the bottom and covering the side one with my finger. Maybe radiusing the hole with Dremel could fix that.
Happy camper I am. Thanks everyone for the assistance and especially @Two_Bears.
Sent from Uranus using Tapatalk
Nice looking coil and nice looking setupWell, I did it... first coil build ever.
About 7 wraps of 28ga Kanthal on a 3mm diameter tool. 1.5 ohms.
This flat top bellcap KFL+ V2 Frankenstein is good... real good. Flavor is right there with my Vika Fantasy, and I haven't found anything that i could say that about.
My only small complaint is the air hole whistle. I ended up taking the airflow screw out of the bottom and covering the side one with my finger. Maybe radiusing the hole with Dremel could fix that.
Happy camper I am. Thanks everyone for the assistance and especially @Two_Bears.
Sent from Uranus using Tapatalk
I have the right tap for the 510 replacement connector but not for the actual 510 threadIn wood a 1/4" hole will be snug enough that it takes some pressure to force it in. Metal... got the right tap?
Or at least helped keep them open!
I have the right tap for the 510 replacement connector but not for the actual 510 thread
When you just can't even...
Well, I did it... first coil build ever.
About 7 wraps of 28ga Kanthal on a 3mm diameter tool. 1.5 ohms.
This flat top bellcap KFL+ V2 Frankenstein is good... real good. Flavor is right there with my Vika Fantasy, and I haven't found anything that i could say that about.
My only small complaint is the air hole whistle. I ended up taking the airflow screw out of the bottom and covering the side one with my finger. Maybe radiusing the hole with Dremel could fix that.
Happy camper I am. Thanks everyone for the assistance and especially @Two_Bears.
Sent from Uranus using Tapatalk
I use the bunny-ear method. After tucking down the wick, I take a blue little screwdriver and pull the wick away from the juicechannels. That works great to avoid dryhits.Wabbit ears!
Coil, wick but do not trim... instead bring the tails of the wick upwards and slide the barrel over the wick. When the barrel is screwed down, trim the wicks just above the top of the barrel. Separate the wicks and genty tuck into either side of the coil. Use a small screwdriver or sharp tweezers to avoid distorting the coil.
Hope everyone has a fantastic Friday! Just wanted to say thanks for all your help, if it wasn't for you, I'd have never gotten in to the satisfying hobby of all things vaping DIY! It's nice to have such a great bunch of people willing to help. I usually get an answer to a burning question within a half hour.
Oh, and I'm writing this while tootling![emoji4]