Uwell Crown 3 mini spitting juice
- Thread starter Marybratti
- Start date
- th_trl_thread_readers 0
-
- Tags
- uwell crown 3
- Status
Try opening the airflow completely and blowing into it while it's wrapped in a paper towel. Do this several times. Then wipe it off and fire it at the highest Wattage setting of the coil. Do this in three second increments with five seconds between firings. Might work.
What do you have the airflow set at? Closing it off too much might result in flooding the coil.
Sent from my SM-G955U using Tapatalk
Sent from my SM-G955U using Tapatalk
What is the pg/vg ratio of the liquid you use?
When you say " tryed lower and higher temps " do you mean lower & higher watts / power levels?
If so how high didja go? crown 3 heads seem to take quite a bit of power to not blubber & spit, many say they take a few tankfuls to break in & work satisfactorily.
If you meant lower &higher temperature using TC are you using SS 316 mode?
Or entering a tcr value suitable for ss316?
.25Ω is sus316 watt/ss tc.
.5Ω is sus316 watt/ss tc.
.4Ω is kanthal watt mode only.
When you say " tryed lower and higher temps " do you mean lower & higher watts / power levels?
If so how high didja go? crown 3 heads seem to take quite a bit of power to not blubber & spit, many say they take a few tankfuls to break in & work satisfactorily.
If you meant lower &higher temperature using TC are you using SS 316 mode?
Or entering a tcr value suitable for ss316?
.25Ω is sus316 watt/ss tc.
.5Ω is sus316 watt/ss tc.
.4Ω is kanthal watt mode only.
Last edited:
70 pg / 30vg or 30pg / 70 vg?
High % Vg should work better than high % Pg in the crown3.
Temp? do you mean 55 watts / 70 watts?
Are you taking long smooth medium strength inhales / MTL
Or, short hard fast strong inhales / DTL?
Trying to MTL a delivery device designed for DTL is going to create problems like you're having.
Are all the o rings /seals in place & undamaged?
Is the head tightly installed into the base?
Could be a stuck o ring from a previous head in the base.
High % Vg should work better than high % Pg in the crown3.
Temp? do you mean 55 watts / 70 watts?
Are you taking long smooth medium strength inhales / MTL
Or, short hard fast strong inhales / DTL?
Trying to MTL a delivery device designed for DTL is going to create problems like you're having.
Are all the o rings /seals in place & undamaged?
Is the head tightly installed into the base?
Could be a stuck o ring from a previous head in the base.
Yes watts. I've taken this thing apart and replaced o rings. Cleaned it changed coils 3 times. Still get a coating of juice on my tounge after I hit it 3 times I shake upside-down and juice comes out the tip.
Okay, watts.
What about the rest of the questions, without as much info as possible hard to give much help.
70Pg / 30Vg? or 30Pg / 70Vg?
70 % Pg is going to be too thin to work properly, the head will always be a flooded state.
MTL slow smooth or DTL hard fast inhale?
Also the crown3 has a less than stellar reputation, many folks struggled with them to the point of no longer using them, of course many also seem to get them to work well.
What about the rest of the questions, without as much info as possible hard to give much help.
70Pg / 30Vg? or 30Pg / 70Vg?
70 % Pg is going to be too thin to work properly, the head will always be a flooded state.
MTL slow smooth or DTL hard fast inhale?
Also the crown3 has a less than stellar reputation, many folks struggled with them to the point of no longer using them, of course many also seem to get them to work well.
70 vg. I'm not taking super long inhales it not like hot spits of juice. It's more like a coating of juice in my mouth.
Okay, watts & 70% vg, o rings & seal in place & undamaged.
Is there an o ring from a previous head stuck in the base?
It is a frequent occurrence, the head to base seal is on the head, if there is an o ring in the base where the head threads in, it shouldn't be there.
MTL & DTL are two completely different methods of inhaling, and are two completely different types / styles / designs of delivery devices 'tanks'.
MTL is a steady smooth medium strength inhale / generally collect vapor in mouth then inhale.
DTL is a hard rapid inhale, really strong drag inhaling vapor deeply & directly into lungs.
Trying to MTL on a delivery device 'tank' that is designed for DTL will cause issues like you're having.
Wet sometimes sputtery vape that leaves a feeling & taste of liquid in your mouth / on tongue, with constant liquid accumulating in air tube & drip tip. Liquid accumulation gets worse with almost every vape, liquid runs or drips out of air tube / drip tip if inverted or shaken, liquid gets in mouth if air tube & drip tip aren't dried every few vapes.
The crown 3 is a DTL type/style/design delivery device, there really isn't much you can do to get satisfactory results when attempting to use it MTL.
The aspire nautilus or nautilus 2 would be examples of MTL delivery devices 'tanks'.
You can try drying the center/air tube & drip tip with a twisted piece of napkin or paper towel maybe a qtip occasionally. Even if that means every 3 vapes.
Is there an o ring from a previous head stuck in the base?
It is a frequent occurrence, the head to base seal is on the head, if there is an o ring in the base where the head threads in, it shouldn't be there.
MTL & DTL are two completely different methods of inhaling, and are two completely different types / styles / designs of delivery devices 'tanks'.
MTL is a steady smooth medium strength inhale / generally collect vapor in mouth then inhale.
DTL is a hard rapid inhale, really strong drag inhaling vapor deeply & directly into lungs.
Trying to MTL on a delivery device 'tank' that is designed for DTL will cause issues like you're having.
Wet sometimes sputtery vape that leaves a feeling & taste of liquid in your mouth / on tongue, with constant liquid accumulating in air tube & drip tip. Liquid accumulation gets worse with almost every vape, liquid runs or drips out of air tube / drip tip if inverted or shaken, liquid gets in mouth if air tube & drip tip aren't dried every few vapes.
The crown 3 is a DTL type/style/design delivery device, there really isn't much you can do to get satisfactory results when attempting to use it MTL.
The aspire nautilus or nautilus 2 would be examples of MTL delivery devices 'tanks'.
You can try drying the center/air tube & drip tip with a twisted piece of napkin or paper towel maybe a qtip occasionally. Even if that means every 3 vapes.
Last edited:
pretty odd for a sub ohm tank, just make sure to find your sweet spot of wattage sometimes my rta tank spit some hot juice in my mouth when i vape, but when i lowered the wattage to 45 i never experienced that again. good luck fixing it
My Crown 3 (not the mini) spits juice sometimes, even floods the tank. The coils seem easy to over-prime on first use. But if you get them humming they seem to be OK.
- Status
Similar threads
- Locked
